Wall Data Inc.
B. Clouston
Z. Kielczewski
Cisco Systems
W. Kwan
Jupiter Technology Inc.
B. Moore
IBM
October 1996
Definitions of Managed Objects for APPC using SMIv2
Status of this Memo
-
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Table of Contents
-
1. Introduction ........................................... 1 2. The SNMP Network Management Framework .................. 1 3. Overview ............................................... 2 3.1 APPC MIB structure ...................................... 4 4. Definitions ............................................ 10 5. Acknowledgments ........................................ 123 6. References ............................................. 123 7. Security Considerations ................................ 123 8. Authors' Addresses ..................................... 124
1. Introduction
-
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines objects for managing the configuration, monitoring and controlling of network devices with APPC (Advanced Program-to-Program Communications) capabilities. This memo identifies managed objects for the SNA LU6.2 protocols.
2. The SNMP Network Management Framework
-
The SNMP Network Management Framework consists of several components. For the purpose of this specification, the applicable components of the Framework are the SMI and related documents [2, 3, 4], which define the mechanisms used for describing and naming objects for the purpose of management.
The Framework permits new objects to be defined for the purpose of experimentation and evaluation.
3. Overview
-
This document identifies the proposed set of objects for managing the configuration, monitoring and controlling devices with APPC capabilities. APPC is the aspect of SNA which supports peer-to-peer communication, and provides the interface for applications to communicate. In this document, we will describe LU6.2 protocol- specific managed objects.
This document describes both dependent and independent LU 6.2 protocols.
A dependent LU requires assistance from an SSCP in order to activate an LU 6.2 session. An independent LU is able to activate an LU 6.2 session without assistance from the SSCP. If the agent supports dependent LU 6.2 only, the SNA NAU MIB, RFC 1666 [7] is used instead to represent those objects.
Local LUs and partner LUs connect with each other using sessions. Multiple different sessions can be established between LUs with characteristics defined by Modes. Session limits within a defined Mode are negotiated between the local and partner LUs using a protocol called CNOS (Change Number of Sessions).
Transaction Programs (TPs) are applications that use sessions to communicate with each other. Multiple TPs can use the same session, but not at the same time. A single usage of a session is called a conversation. While a session can stay active for a long time, a conversation can come up and down based on usage by the TPs.
Common Programming Interface - Communications (CPI-C) is a standard API (Application Programming Interface) for APPC and OSI TP that is used by TPs for accessing conversations. Although, many of the CPI-C objects in this MIB are relevant to both APPC and OSI TP, the intention is for managing APPC products only.
SNA names such as LU names, CP names, mode names, and COS names can be padded with space characters in SNA formats. These space characters are insignificant. For example, in a BIND RU a mode name of "#INTER" with a length of 6 is identical to a mode name of "#INTER " with a length of 8. However, in this MIB, insignificant space characters are not included by the agent. Using the mode name from the previous example, an agent would return a length of 6 and the string "#INTER" with no space characters for appcModeAdminModeName, regardless of how it appears in the BIND RU or in internal storage. The lone exception is the all blank mode name, for which the agent returns a length of 8 and the string " " (8 space characterss).
When an SNA name is functioning as a table index, an agent shall treat trailing space characters as significant. If a Management Station requests the objects from a row with index "#INTER ", the agent does not match this to the row with index "#INTER". Since an agent has no insignificant space characters in any of its table indices, the only reason for a Management Station to include them would be to start GetNext processing at a chosen point in a table. For example, a GetNext request with index "M " would start retrieval from a table at the first row with an 8-character index beginning with M or a letter after M. The SNA/APPC terms and overall architecture are documented in [1], [5], and [6].
Highlights of the management functions supported by the APPC MIB module include the following:
o Activating and deactivating statistics keeping and counting. o Activating and deactivating tracing. o Issuing CNOS processing verbs/commands for INITIALIZE_SESSION_LIMIT, CHANGE_SESSION_LIMIT and RESET_SESSION_LIMIT. o Monitoring of parameters related to local LU, partner LU, modes, TPs and CPI-C side information. o Deactivating sessions. o Monitoring of LU6.2-specific session operational parameters and statistics, historical information about abnormally terminated sessions, and information about APPC sessions that are transported by APPN HPR. o Monitoring of conversation operational parameters, and historical information about abnormally terminated sessions.This MIB module does not support:
o Modifying APPC defaults. o Creating and deleting partner LUs, modes, TPs, and CPI-C side information tables. o Modifying parameters related to local LU, partner LU, modes, TPs, and CPI-C side information. o Activating or deactivating local LUs. o Activating or deactivating partner LUs. o Activating or deactivating conversations. o Activating or deactivating Transaction Programs. o Activating sessions. o Traps
3.1. APPC MIB Structure
-
The APPC MIB module contains six groups of objects:
o appcGlobal - objects related to global defaults and controls. In addition, CNOS processing objects are also part of this group. o appcLu - objects related to LU6.2-specific local and partner LU, mode definition, monitoring and control. o appcTp - objects related to transaction program definition, monitoring and control. o appcSession - objects related to LU6.2-specific session monitoring. o appcConversation - objects related to conversation monitoring. o appcCPIC - objects related to related CPI-C side information.These groups are described below in more detail.
The objects related to LU6.2 are generally organized into two types of tables: the Admin and Oper tables.
The "Admin" table contains read-only objects which contain default or expected configuration values. This MIB does not create or modify configuration values. The "Oper" table contains objects which provide current operational values, such as state values or negotiated parameters, for dynamic or configured objects. Dynamic objects are created by the APPC system using one of the templates provided in the "Admin" table. Configured objects usually have a one-to-one relationship between "Admin" and "Oper" entries. However, some "Admin" values may have changed since the object became operational, such that the "Oper" values may no longer be based on the "Admin" values. The "Admin" entry could even be deleted. For example, some implementations may allow a mode definition (appcModeAdminEntry) to be deleted even while an active session was using this mode (appcModeOperEntry still exists). Where appropriate, the "Oper" table may include initial starting values for objects that can be reconfigured while operational. How the "Admin" values are changed or deleted is outside the scope of this MIB.
3.1.1. appcGlobal group
-
The appcGlobal group consists of the following tables and objects:
- appcCntrlAdminGroup
This group of objects controls whether certain statistics and counters (e.g., session counters and RSCV collection) should be maintained by the Agent. In addition, the ability to activate and deactivate tracing is also supported through objects in this group. These objects are for Agent implementations that wish to provide this level of operational control and are optional.
The objects in this group represent the desired state, with the actual operational values in appcCntlOperGroup.
These objects can be generated initially, after startup of SNA service, by the Agent which uses information from the Node configuration file. Subsequent modifications of object values is possible by a Management station. The modifications to these objects can be saved in the Node configuration file for the next startup (i.e., restart or next initialization) of SNA service, but the mechanism for this function is not defined in this document.
- appcCntrlOperGroup
This group of objects monitors whether certain statistics and counters (e.g., session counters and RSCV collection ) are maintained by an Agent. In addition, the ability to monitor tracing activity is also supported through objects in this group.
This table represents the actual operational state. These states can be modified via objects in the appcCntrlAdminGroup.
- appcGlobalObjects
These objects describe global information such as APPC system start time, the control point name, and default LU 6.2 configuration values. The type of default configuration information includes mode name, LU, and maximum logical record size.
- appcCnosControl
These objects allows for issuing of CNOS commands relative to a local and partner LU pair and a Mode. They support the following CNOS commands: INITIALIZE_SESSION_LIMIT, CHANGE_SESSION_LIMIT and RESET_SESSION_LIMIT.
The objects in this group can be modified by a Management Station.
This group consists of objects that are relevant to the CNOS commands parameters, which a Management Station needs to set. After setting the parameters of a CNOS command, the Management Station will set the control object (appcCnosCommand) to request the Agent to issue the appropriate CNOS command.
3.1.2. appcLu group
-
The appcLu group consists of the following tables:
- appcLluAdminTable
This table contains objects which describe specific LU6.2 local LU configuration information. The type of information includes the maximum number of sessions supported and compression parameters.
- appcLluOperTable
This table contains objects which describe specific LU6.2 local LU operational information. The type of information includes the maximum number of sessions supported, the number of sessions currently active, and compression parameters.
- appcLuPairAdminTable
This table contains objects which describe local LU and partner LU configuration information. The type of information includes security information and whether parallel sessions are supported.
For those implementations that have partner LU definitions associated with each local LU, multiple entries with the same appcLuPairAdminParLuName could exist with different appcLuPairAdminLocLuName. For those implementations in which partner LU definitions apply to all local LUs, the appcLuPairAdminLocLuName is set to '*ALL'.
- appcLuPairOperTable
This table contains objects which describe partner/local LU pair run- time operational information. The type of information includes security information and whether parallel sessions are supported.
Although the Admin (appcLuPairAdminTable) table entries could be global to all local LUs in a Node, an entry in this Oper table is always associated with one local LU.
A row in this table is created as soon as there is an active session between the local and partner LU. Two entries are present when both LUs in a pair are local.
- appcModeAdminTable
This table contains objects which describe Mode configuration information. The type of information includes the mode name and maximum session limit.
For those implementations that have Mode definitions associated with each local and partner LU pair, multiple entries with the same appcModeAdminModeName could exist with different appcModeAdminLocLuName and appcModeAdminParLuName. For those implementations in which Mode definitions apply to all local and/or all partner LUs, the appcModeAdminLocLuName and/or appcModeAdminParLuName are set to '*ALL'.
- appcModeOperTable
This table contains objects which describe Mode run-time operational information for each local/partner LU pair. The type of information includes the mode name and maximum session limit.
Although the Admin table entries could be global to all local and partner LUs in a Node, the Oper table entries are always associated with one local and partner LU pair.
A row in this table is created as soon as there is an active session between local and partner LU for this Mode. Two entries are present when both LUs in a pair are local.
3.1.3. appcTp group
-
The appcTp group consists of the following table:
- appcTpAdminTable
This table contains objects which describe transaction program (TP) configuration information. The type of information includes the TP name and TP operation, indicating how the TP will be started.
For those implementations that have TP definitions associated with each local LU, multiple entries with the same appcTpAdminTpName could exist with different appcTpAdminLocLuName. For those implementations in which TP definition applies to all local LUs, it will have appcTpAdminLocLuName set to '*ALL'.
There is no appcTpOperTable. Run-time information about TP tends to be product-specific (e.g., process Id), and much of the information can be derived from the conversation tables.
3.1.4. appcSession group
-
The appcSession group consists of the following tables:
- appcActSessTable
This table contains objects which describe LU6.2 session information. The type of information includes the PCID and the pacing counts.
- appcSessStatsTable
This table contains statistical information about LU 6.2 sessions. The type of information includes counters of bytes and RUs sent and received.
- appcHistSessTable
This table contains historical information about APPC sessions that have terminated abnormally. The type of information includes the unbind type and sense data.
- appcSessRtpTable
This table contains information about LU 6.2 sesions that are being transported by High Performance Routing. The type of information includes the NCEID and TCID.
3.1.5. appcConversation group
-
The appcConversation group consists of the following tables:
- appcActiveConvTable
This table contains objects which describe active conversation information. The type of information includes the state and type. An entry is created by an Agent when the conversation is started, and is removed when the conversation ends.
- appcHistConvTable
This table contains objects which describe historical conversation information about abnormally terminated conversations. The number of entries and how long they are kept depends on the Agent implementation. The type of information inclues the sense data and log data.
3.1.6. appcCPIC group
-
The appcCPIC group consists of the following tables:
- appcCpicAdminTable
This table contains objects which describe CPI-C side information. The type of information includes the symbolic destination name and partner LU name.
For those implementations that have CPI-C definition associated with each local LU, multiple entries with the same appcCpicAdminSymbDestName could exist with different appcCpicAdminLocLuName. For those implementations in which CPI-C definition applies to all local LUs, it will have appcCpicAdminLocLuName set to '*ALL'.
- appcCpicOperTable
This table contains objects which describe CPI-C run-time operational information. The type of information includes the symbolic destination name and partner LU name.
4. Definitions
APPC-MIB DEFINITIONS ::= BEGIN
IMPORTS
-
DisplayString, InstancePointer, TEXTUAL-CONVENTION, DateAndTime FROM SNMPv2-TC mib-2, Counter32, Gauge32, Integer32, TimeTicks, OBJECT-TYPE, MODULE-IDENTITY FROM SNMPv2-SMI-
snanauMIB
FROM SNA-NAU-MIB
-
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF;
-
appcMIB MODULE-IDENTITY
-
LAST-UPDATED "9512150000Z" ORGANIZATION "IETF SNA NAU MIB Working Group" CONTACT-INFO-
-
-
"
-
-
Michael Allen Wall Data Inc. P.O.Box 1120 Duval, WA 98019, USA Tel: 1 206 844 3505 E-mail: mallen@hq.walldata.com Bob Clouston Cisco Systems 7025 Kit Creek Road P.O. Box 14987 Research Triangle Park, NC 27709, USA Tel: 1 919 472 2333 E-mail: clouston@cisco.com Zbigniew Kielczewski Cisco Systems 3100 Smoketree Court Raleigh, NC 27604, USA Tel: 1 919 871 6326 E-mail: zbig@cisco.com William Kwan Jupiter Technology Inc. 200 Prospect Street Waltham, MA 02254, USA Tel: 1 617 894 9300, x423 E-mail: billk@jti.com Bob Moore IBM Corporation 800 Park Offices Drive CNMA/664 P.O. Box 12195 Research Triangle Park, NC 27709, USA Tel: 1 919 254 4436 E-mail: remoore@ralvm6.vnet.ibm.com " DESCRIPTION "This is the MIB module for objects used to manage network devices with APPC capabilities." -
::= { snanauMIB 3 }
appcObjects OBJECT IDENTIFIER ::= { appcMIB 1 }
appcGlobal OBJECT IDENTIFIER ::= { appcObjects 1 }
appcLu OBJECT IDENTIFIER ::= { appcObjects 2 }
appcTp OBJECT IDENTIFIER ::= { appcObjects 3 }
appcSession OBJECT IDENTIFIER ::= { appcObjects 4 }
appcConversation OBJECT IDENTIFIER ::= { appcObjects 5 }
appcCPIC OBJECT IDENTIFIER ::= { appcObjects 6 }
-- *********************************************************************
-- Objects in this MIB are used to model an SNA device that supports
-- APPC LUs.
-- Following is the overall organization of the MIB.
--
-- 1. APPC Global Objects - global values, defaults,
-- controls (including CNOS)
-- 2. APPC Defined Lu Tables - Admin and Oper
-- 3. APPC Defined LU Pair Tables - Admin and Oper
-- 4. APPC Mode Tables - Admin and Oper
-- 5. APPC TP Tables - Admin only
-- 6. APPC Session Tables - Active, Stats, History, RTP
-- 7. APPC Conversation Table - Active, History
-- 8. APPC CPIC side info - Admin and Oper
-- *********************************************************************
-- *********************************************************************
-- Textual Convention
-- ---------------------------------------------------------------------
SnaSenseData ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"To facilitate their display by a Management Station, sense
data objects in the MIB are represented as DisplayStrings of
size 8. Eight '0' characters indicates that no sense data
identifying an SNA error condition is available."
SYNTAX DisplayString (SIZE (8))
-- *********************************************************************
-- APPC Control Objects
-- ---------------------------------------------------------------------
-- The following objects allow:
-- * the collection of APPC Session information counters
-- to be started and stopped
-- * the collection of APPC Session RSCVs
-- to be started and stopped
-- * the collection of APPC tracing information to be started and
-- stopped
--
-- These objects are for implementations that wish to provide
-- this level of operational control. This group is
-- conditionally mandatory in the conformance section of the MIB.
--
-- *********************************************************************
-- *********************************************************************
-- Control Admin
-- These objects contain the desired states for the controls.
-- The actual states are in the Oper objects.
-- *********************************************************************
appcCntrlAdminGroup OBJECT IDENTIFIER ::= { appcGlobal 1 }
appcCntrlAdminStat OBJECT-TYPE
-
SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the desired state of statistics collection:
notActive collection of counters is not active.
active collection of counters is active.
-
-
-
When this object is set to notActive, all of the entries are removed from the appcSessStatsTable."
-
::= { appcCntrlAdminGroup 1 } -
appcCntrlAdminRscv OBJECT-TYPE
-
SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the desired state of RSCV information collection: notActive collection of route selection control vectors is not active. active collection of route selection control vectors is active." ::= { appcCntrlAdminGroup 2 }
appcCntrlAdminTrace OBJECT-TYPE
-
SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the desired state of tracing: notActive collection of tracing information is not active active collection of tracing information is active" ::= { appcCntrlAdminGroup 3 }
appcCntrlAdminTraceParm OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the parameter to be used in conjunction with activating tracing. The actual content is implementation dependent." ::= { appcCntrlAdminGroup 4 }
-- *********************************************************************
-- Control Oper
-- These objects contain the actual states of the controls.
-- *********************************************************************
appcCntrlOperGroup OBJECT IDENTIFIER ::= { appcGlobal 2 }
appcCntrlOperStat OBJECT-TYPE
-
SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current collection options in effect:
notActive collection of counters is not active.
active collection of counters is active.
-
-
-
Statistical entries are present in the appcSessStatsTable only when the value of this object is 'active'."
-
::= { appcCntrlOperGroup 1 } -
appcCntrlOperStatTime OBJECT-TYPE
-
-
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Time since the appcCntrlOperStat object last changed.
This time is in hundreds of a second."
-
::= { appcCntrlOperGroup 2 } -
appcCntrlOperRscv OBJECT-TYPE
-
SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current collection options in effect: notActive collection of route selection control vectors is not active. active collection of route selection control vectors is active." ::= { appcCntrlOperGroup 3 }
appcCntrlOperRscvTime OBJECT-TYPE
-
-
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Time since the appcCntrlOperRscv object last changed.
This time is in hundreds of a second."
-
::= { appcCntrlOperGroup 4 } -
appcCntrlOperTrace OBJECT-TYPE
-
SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current state of tracing: notActive collection of tracing information is not active. active collection of tracing information is active." ::= { appcCntrlOperGroup 5 }
appcCntrlOperTraceTime OBJECT-TYPE
-
-
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Time since the appcCntrlOperTrace object last changed.
This time is in hundreds of a second."
-
::= { appcCntrlOperGroup 6 } -
appcCntrlOperTraceParm OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the parameter used in conjunction with activating tracing. The actual content is implementation dependent." ::= { appcCntrlOperGroup 7 }
-- ******************************************************************
--
-- APPC global settings
--
-- ******************************************************************
appcGlobalObjects OBJECT IDENTIFIER ::= { appcGlobal 3 }
appcUpTime OBJECT-TYPE
-
-
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The time, in hundredths of a second, since the
APPC portion of the system was last reinitialized."
-
::= { appcGlobalObjects 1 } -
appcDefaultModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the mode name to be used under the following conditions:-
-
-
When an incoming BIND request contains a mode name not defined at the local node. The parameters defined for this mode are used for the inbound implicit mode capability.
When an APPC program issues an [MC_]ALLOCATE, [MC_]SEND_CONVERSATION, or CNOS verb, or when a CPI-C program issues an Allocate (CMALLC) call,
specifying a mode name not defined at the local node. The parameters defined for this mode are used for the outbound implicit mode capability.
This mode name must match a defined entry in the appcModeAdminTable."
-
-
::= { appcGlobalObjects 2 } -
appcDefaultLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the name of the local LU that is to serve as the default LU. This is the default LU to which are routed inbound-
-
BIND requests that exclude the secondary LU name. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present. This local LU name must match a defined entry in the appcLluAdminTable."
-
::= { appcGlobalObjects 3 } -
appcDefaultImplInbndPlu OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether or not inbound implicit partner LU support is enabled. The following values are defined: no - Specifies that inbound implicit partner LU support is disabled, which means that an incoming bind that specifies a partner LU that is not defined at the local node will be rejected. yes - Specifies that inbound implicit partner LU support is enabled, which provides the capability to accept an incoming BIND request that contains a partner LU name that is not defined at the local node." ::= { appcGlobalObjects 4 }
appcDefaultMaxMcLlSndSize OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the maximum size of a logical record to be used for a mapped conversation when sending data to either the inbound or outbound implicit partner LU. This size is the maximum number of bytes in a single logical record, as indicated in the LL field of the record. The default value is 32767.
Note that this object does not limit the maximum size that an application program can supply on the Send Data call for a mapped conversation."
-
::= { appcGlobalObjects 5 } -
appcDefaultFileSpec OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "The local file specification that is to be searched by the APPC attach manager when no DEFINE_TP verb has been issued for the TP name received on an incoming attach. In this case, the attach manager will attempt to start a program whose file name is the same as the incoming TP name. If found, the program is loaded. If not found, the attach is rejected.-
-
The value '*' indicates that the normal search path for executable programs is to be used for locating an undefined transaction program.
-
-
A null string indicates that there is no default file
specification for undefined transaction programs."
-
::= { appcGlobalObjects 6 }
appcDefaultTpOperation OBJECT-TYPE
-
SYNTAX INTEGER { other(1), queuedOperatorStarted(2), queuedOperatorPreloaded(3), queuedAmStarted(4), nonqueuedAmStarted(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies how the program will be started.-
-
-
other - Specifies that the default TP operation is none of
-
-
the methods specified below. It may be a product-specific method.
-
queuedOperatorStarted - Specifies that one version of the
-
-
program will be run at a time. If an incoming attach arrives and the program has not been started yet, APPC will issue a message to the operator to start the specified program. Subsequent attaches that arrive while the program is active will be queued.
-
-
-
-
queuedOperatorPreloaded - Specifies that one version
-
-
-
-
-
-
of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, the Attach will be rejected. The APPC attach manager determines that a TP has started upon reception of an APPC RECEIVE_ALLOCATE verb, or a CPI-C Accept_Conversation (CMACCP) or Specify_Local_TP_Name (CMSLTP) call. No message is sent to the operator. Subsequent attaches that arrive while the program is active are queued.
-
queuedAmStarted - Specifies that one version of the
-
-
program will be run at a time and will be started by the APPC attach manager. Subsequent attaches that arrive while the program is active will be queued.
-
nonqueuedAmStarted - Specifies that multiple copies of
-
-
the program will be run at a time and will be started by the APPC attach manager. "
-
-
-
-
::= { appcGlobalObjects 7 } -
appcDefaultTpConvSecRqd OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether or not conversation security will be used for default TPs. no - Specifies that the incoming attach does not have to contain security information. yes - Specifies that the incoming attach must contain valid authentication information (e.g., user ID and password)." ::= { appcGlobalObjects 8 }
appcLocalCpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the name of the local control point. This field is from 0 to 17 characters in length, including a period (.) which-
-
separates the NetId from the NAU name if the NetId is present. A null string indicates that the value is unknown."
-
::= { appcGlobalObjects 9 } -
appcActiveSessions OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the total number of active APPC sessions supported by this implementation. Sessions for which both LUs are local are counted twice."
-
::= { appcGlobalObjects 10 } -
appcActiveHprSessions OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the total number of active HPR APPC sessions."
::= { appcGlobalObjects 11 }
-- ******************************************************************
-- APPC CNOS control
--
-- This group contains objects for issuing APPC Change-Number-of-Session
-- (CNOS) commands to a specific mode. Specifically, the commands
-- supported are:
-- INITIALIZE_SESSION_LIMIT
-- CHANGE_SESSION_LIMIT
-- RESET_SESSION_LIMIT
--
--
-- ******************************************************************
appcCnosControl OBJECT IDENTIFIER ::= { appcGlobal 4 }
appcCnosCommand OBJECT-TYPE
-
SYNTAX INTEGER { initSesslimit(1), changeSesslimit(2), resetSesslimit(3) } MAX-ACCESS read-write STATUS current-
DESCRIPTION
-
"Specifies the CNOS command or verb to issue. First set the values of the particular CNOS parameter objects (from the range { appcCnosControl 2 } through { appcCnosControl 8 }) that apply to the CNOS command to be executed, set the three CNOS target objects ({ appcCnosControl 9 } through { appcCnosControl 11 }), then set this object to the command to be executed.
Here is the list of parameter objects that must be set for each of the CNOS commands:
-
INIT_SESSION_LIMIT -
appcCnosMaxSessLimit
appcCnosMinCwinLimit
appcCnosMinClosLimit
appcCnosTargetLocLuName
appcCnosTargetParLuName
appcCnosTargetModeNameCHANGE_SESSION_LIMIT -
appcCnosMaxSessLimit
appcCnosMinCwinLimit
appcCnosMinClosLimit
appcCnosResponsible
appcCnosTargetLocLuName
appcCnosTargetParLuName
appcCnosTargetModeName
-
RESET_SESSION_LIMIT - appcCnosResponsible appcCnosDrainPart appcCnosForce appcCnosTargetLocLuName appcCnosTargetParLuName appcCnosTargetModeName " ::= { appcCnosControl 1 } -
appcCnosMaxSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION-
"Specifies the maximum value that the local LU is to use, during CNOS processing, for the session limit. The local LU, as a target LU, will negotiate a higher session limit it receives in the CNOS request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value.
-
-
If set (i.e., greater than 0), this overrides the maximum
session limit defined in the appcModeAdminTable.
-
-
-
This parameter should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies to the INITIALIZE_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs."
DEFVAL { 0 }
-
::= { appcCnosControl 2 } -
appcCnosMinCwinLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION-
"Specifies the default minimum contention winner sessions limit.
This parameter should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies to the INITIALIZE_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs."
DEFVAL { 0 }
-
::= { appcCnosControl 3 } -
appcCnosMinClosLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION-
"Specifies the default minimum contention loser sessions limit.
This parameter should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies to the INITIALIZE_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs."
DEFVAL { 0 }
-
::= { appcCnosControl 4 } -
appcCnosDrainSelf OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the local LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the local LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stopped or BIS protocol).-
-
This parameter should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies only to the RESET_SESSION_LIMIT verb."
DEFVAL { no }
-
::= { appcCnosControl 5 } -
appcCnosDrainPart OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the partner LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the partner LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stop or BIS protocol).-
-
This parameter should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies only to the RESET_SESSION_LIMIT verb."
DEFVAL { yes }
-
::= { appcCnosControl 6 } -
appcCnosResponsible OBJECT-TYPE
-
SYNTAX INTEGER { source(1), target(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies which LU is responsible for selecting and deactivating sessions as a result of a change that decreases the session limit or the maximum number of contention winner sessions for the source or target LU. If no session need to be deactivated, this parameter is ignored. source - specifies that the source (local) LU is responsible. The target (partner) LU cannot negotiate this value. target - specifies that the target (partner) LU is responsible. The target LU can negotiate this value to source.-
-
This parameter should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies to the RESET_SESSION_LIMIT and CHANGE_SESSION_LIMIT verbs."
DEFVAL { source }
-
::= { appcCnosControl 7 } -
appcCnosForce OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the local LU should force the resetting of the session limit when certain error conditions occur that prevent the successful exchange of CNOS request and reply.
This parameter should be set to the desired value before
-
-
-
setting the command (appcCnosCommand).
This parameter applies only to the RESET_SESSION_LIMIT verb."
DEFVAL { no }
-
::= { appcCnosControl 8 } -
appcCnosTargetLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-write STATUS current DESCRIPTION "The SNA name of the local LU to which the CNOS command is to be applied. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
This object should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies to all CNOS verbs."
-
::= { appcCnosControl 9 } -
appcCnosTargetParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-write STATUS current DESCRIPTION "The SNA name of the partner LU to which the CNOS command is to be applied. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
This object should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies to all CNOS verbs."
-
::= { appcCnosControl 10 } -
appcCnosTargetModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the mode name to which the CNOS command is to be-
-
applied.
This object should be set to the desired value before setting the command (appcCnosCommand).
This parameter applies to all CNOS verbs."
-
-
::= { appcCnosControl 11 }
-- *********************************************************************
-- APPC LU information
-- ---------------------------------------------------------------------
-- Local LU
-- Partner LU
-- Mode
-- *********************************************************************
-- *********************************************************************
-- APPC Local LU
--
-- The entries in the following tables provide information for
-- independent and dependent LU 6.2.
--
-- *********************************************************************
-- *********************************************************************
-- APPC Local LU Admin Table
-- Objects in this table contain default or expected configuration
-- values for local 6.2 LUs.
-- *********************************************************************
appcLluAdminTable OBJECT-TYPE
-
-
SYNTAX SEQUENCE OF AppcLluAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"APPC Local LU Admin Table."
-
::= { appcLu 1 } -
appcLluAdminEntry OBJECT-TYPE
-
-
SYNTAX AppcLluAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Information about local APPC LUs. "
INDEX { appcLluAdminName }
-
-
::= { appcLluAdminTable 1 }
AppcLluAdminEntry ::= SEQUENCE {
appcLluAdminName DisplayString,
appcLluAdminDepType INTEGER,
appcLluAdminLocalAddress OCTET STRING,
appcLluAdminSessLimit Integer32,
appcLluAdminBindRspMayQ INTEGER,
appcLluAdminCompression INTEGER,
appcLluAdminInBoundCompLevel INTEGER,
appcLluAdminOutBoundCompLevel INTEGER,
appcLluAdminCompRleBeforeLZ INTEGER,
appcLluAdminAlias DisplayString
}
appcLluAdminName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcLluAdminEntry 1 }
appcLluAdminDepType OBJECT-TYPE
-
SYNTAX INTEGER { dependent(1), independent(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value identifies whether the LU is dependent or independent." ::= { appcLluAdminEntry 2 }
appcLluAdminLocalAddress OBJECT-TYPE
-
-
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The local address for this LU is a byte with a value ranging from 0 to 254. For dependent LUs, this value ranges from 1 to
254; for independent LUs this value is always 0."
-
::= { appcLluAdminEntry 3 } -
appcLluAdminSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"The maximum number of sessions supported by this LU."
-
::= { appcLluAdminEntry 4 }
appcLluAdminBindRspMayQ OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the local LU, as the sender of a BIND request, allows a partner partner LU to delay sending the BIND response if the partner LU cannot process the BIND request immediately." ::= { appcLluAdminEntry 5 }
appcLluAdminCompression OBJECT-TYPE
-
SYNTAX INTEGER { prohibited(1), required(2), negotiable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated." ::= { appcLluAdminEntry 6 }
appcLluAdminInBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcLluAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcLluAdminEntry 7 }
appcLluAdminOutBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcLluAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcLluAdminEntry 8 }
appcLluAdminCompRleBeforeLZ OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used." ::= { appcLluAdminEntry 9 }
appcLluAdminAlias OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "A local alias for the local LU. If not known or not applicable, this object contains a zero-length string." ::= { appcLluAdminEntry 10 }
-- *********************************************************************
-- APPC Local LU Oper Table
-- Objects in this table contain current operational values, such -- as state values or negotiated parameters, for local 6.2 LUs. -- *********************************************************************
appcLluOperTable OBJECT-TYPE
-
SYNTAX SEQUENCE OF AppcLluOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC Local LU Operational Table." ::= { appcLu 2 }
appcLluOperEntry OBJECT-TYPE
-
-
SYNTAX AppcLluOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Information about local APPC LUs."
INDEX { appcLluOperName }
-
-
::= { appcLluOperTable 1 }
AppcLluOperEntry ::= SEQUENCE {
appcLluOperName DisplayString,
appcLluOperDepType INTEGER,
appcLluOperLocalAddress OCTET STRING,
appcLluOperSessLimit Integer32,
appcLluOperBindRspMayQ INTEGER,
appcLluOperCompression INTEGER,
appcLluOperInBoundCompLevel INTEGER,
appcLluOperOutBoundCompLevel INTEGER,
appcLluOperCompRleBeforeLZ INTEGER,
appcLluOperAlias DisplayString,
appcLluOperActiveSessions Gauge32
}
appcLluOperName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcLluOperEntry 1 }
appcLluOperDepType OBJECT-TYPE
-
SYNTAX INTEGER { dependent(1), independent(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This value identifies whether the LU is dependent or independent." ::= { appcLluOperEntry 2 }
appcLluOperLocalAddress OBJECT-TYPE
-
-
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The local address for this LU is a byte with a value ranging from 0 to 254. For dependent LUs, this value ranges from 1 to 254; for independent LUs this value is always 0."
-
::= { appcLluOperEntry 3 } -
appcLluOperSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"The maximum number of sessions supported by this LU."
-
::= { appcLluOperEntry 4 }
appcLluOperBindRspMayQ OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the local LU, as the sender of a BIND request, allows a partner LU to delay sending the BIND response if the partner LU cannot process the BIND request immediately." ::= { appcLluOperEntry 5 }
appcLluOperCompression OBJECT-TYPE
-
SYNTAX INTEGER { prohibited(1), required(2), negotiable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated." ::= { appcLluOperEntry 6 }
appcLluOperInBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcLluOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcLluOperEntry 7 }
appcLluOperOutBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcLluAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcLluOperEntry 8 }
appcLluOperCompRleBeforeLZ OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION-
-
"Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used."
-
::= { appcLluOperEntry 9 } -
appcLluOperAlias OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "A local alias for the local LU. If not known or not applicable, this object contains a zero-length string." ::= { appcLluOperEntry 10 }
appcLluOperActiveSessions OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the total number of active APPC sessions for this LU."
-
-
::= { appcLluOperEntry 11 }
-- *********************************************************************
-- APPC LU Pair Admin Table
-- Objects in this table contain default or expected configuration
-- values for 6.2 LU pairs. An LU pair consists of a local LU and
-- a partner LU, which may or may not be local.
-- *********************************************************************
appcLuPairAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcLuPairAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Partner LU administrative Table"
::= { appcLu 3 }
appcLuPairAdminEntry OBJECT-TYPE
-
-
SYNTAX AppcLuPairAdminEntry
MAX-ACCESS not-accessible
STATUS currentDESCRIPTION
-
"Entry of APPC Partner LU Information Table.
It is indexed by the local and partner LU Names."
INDEX { appcLuPairAdminLocLuName,
appcLuPairAdminParLuName } ::= { appcLuPairAdminTable 1 } -
AppcLuPairAdminEntry ::= SEQUENCE {
-
appcLuPairAdminLocLuName DisplayString, appcLuPairAdminParLuName DisplayString, appcLuPairAdminParLuAlias DisplayString, appcLuPairAdminSessLimit Integer32, appcLuPairAdminSessSec INTEGER, appcLuPairAdminSecAccept INTEGER, appcLuPairAdminLinkObjId InstancePointer, appcLuPairAdminParaSessSup INTEGER }
appcLuPairAdminLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU to which this partner LU definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
The reserved value '*ALL' indicates that the partner LU definition applies to all local LUs, and not just to a single local LU."
-
::= { appcLuPairAdminEntry 1 } -
appcLuPairAdminParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcLuPairAdminEntry 2 }
appcLuPairAdminParLuAlias OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string." ::= { appcLuPairAdminEntry 3 }
appcLuPairAdminSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The maximum number of sessions supported by this partner LU."
-
::= { appcLuPairAdminEntry 4 } -
appcLuPairAdminSessSec OBJECT-TYPE
-
SYNTAX INTEGER { required(1), accepted(2), notAllowed(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the type of session-level security information that a local LU will accept on BIND requests it receives from the partner LU. required - Specifies that the BIND request must carry session level verification information that will be verified upon receipt. accepted - Specifies that the BIND request may carry session level verification information that will be verified upon receipt. notAllowed - Specifies that the BIND request must not carry session level verification information." ::= { appcLuPairAdminEntry 5 }
appcLuPairAdminSecAccept OBJECT-TYPE
SYNTAX INTEGER {
-
none(1), conversation(2), alreadyVerified(3), persistentVerification(4), aVandpV(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies support for different levels of access security information in ATTACH requests received from this partner LU.-
-
Possible values are:
-
none - No access security information will be accepted on allocation requests (ATTACH) from this LU. conversation - Allocation requests will not be accepted that include already verified or persistent verification indicators. Accept conversation-level access security information, which must include both a user Id and password, and may also include a profile. alreadyVerified - Allocation requests will be accepted that include already verified indicators. Persistent verification indicators will not be accepted. persistentVerification - Allocation requests will be accepted that include persistent verification indicators. Already verified indicators will not be accepted. aVandpV - Allocation requests will be accepted that include already verified or persistent verification indicators." ::= { appcLuPairAdminEntry 6 } -
appcLuPairAdminLinkObjId OBJECT-TYPE
-
-
SYNTAX InstancePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the link associated with this partner LU. This value points to the row in the table containing information on the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC MIB module). This object may be NULL if the link is not specified or if a link is not applicable (as for APPN-level nodes)."
-
::= { appcLuPairAdminEntry 7 } -
appcLuPairAdminParaSessSup OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Defined Parallel Sessions Supported.-
-
Indicates whether or not multiple sessions between the partner LU and its associated local LU are permitted. Parallel session support also indicates that Change Number of Sessions (CNOS) will be used to negotiate session limits between the LUs."
-
-
::= { appcLuPairAdminEntry 8 }
-- *********************************************************************
-- APPC LU Pair Oper Table
-- Objects in this table contain current operational values, such
-- as state values or negotiated parameters, for 6.2 LU pairs.
-- *********************************************************************
appcLuPairOperTable OBJECT-TYPE
-
SYNTAX SEQUENCE OF AppcLuPairOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of active partner/local LU pairs. Two entries are present in the table when both LUs in a pair are local." ::= { appcLu 4 }
appcLuPairOperEntry OBJECT-TYPE
-
-
SYNTAX AppcLuPairOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry representing one partner/local LU pair."
INDEX { appcLuPairOperLocLuName,
-
-
appcLuPairOperParLuName }
::= { appcLuPairOperTable 1 }
AppcLuPairOperEntry ::= SEQUENCE {
appcLuPairOperLocLuName DisplayString,
appcLuPairOperParLuName DisplayString,
appcLuPairOperParLuAlias DisplayString,
appcLuPairOperSessLimit Integer32,
appcLuPairOperSessSec INTEGER,
appcLuPairOperSecAccept INTEGER,
appcLuPairOperLinkObjId InstancePointer,
appcLuPairOperParaSessSup INTEGER,
appcLuPairOperParaSessSupLS INTEGER,
appcLuPairOperState INTEGER
}
appcLuPairOperLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.
If this object has the same value as appcLluOperName,
then the two entries being indexed apply to the same
resource (specifically, to the same local LU)."
-
::= { appcLuPairOperEntry 1 }
appcLuPairOperParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcLuPairOperEntry 2 }
appcLuPairOperParLuAlias OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current-
DESCRIPTION
-
"A local alias for the partner LU. If not known or
not applicable, this object contains a zero-length
string."
-
::= { appcLuPairOperEntry 3 }
appcLuPairOperSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The maximum number of sessions supported by this partner LU."
-
::= { appcLuPairOperEntry 4 } -
appcLuPairOperSessSec OBJECT-TYPE
-
SYNTAX INTEGER { required(1), accepted(2), notAllowed(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the type of security information that a local LU will accept on BIND requests it receives from the partner LU. required - Specifies that the BIND request must carry session level verification information that will be verified upon receipt. accepted - Specifies that the BIND request may carry session level verification information that will be verified upon receipt. notAllowed - Specifies that the BIND request must not carry session level verification information." ::= { appcLuPairOperEntry 5 }
appcLuPairOperSecAccept OBJECT-TYPE
-
SYNTAX INTEGER { none(1), conversation(2), alreadyVerified(3), persistentVerification(4), aVandpV(5) } MAX-ACCESS read-only-
STATUS current
DESCRIPTION-
"Specifies support for different levels of security acceptance
information in ATTACH requests received from this partner LU.
Possible values are:
-
none - No access security information will be accepted on allocation requests (ATTACH) from this LU. conversation - Allocation requests will not be accepted that include already verified or persistent verification indicators. Accept conversation-level access security information, which must include both a user Id and password, and may also include a profile. alreadyVerified - Allocation requests will be accepted that include already verified indicators. Persistent verification indicators will not be accepted. persistentVerification - Allocation requests will be accepted that include persistent verification indicators. Already verified indicators will not be accepted. aVandpV - Allocation requests will be accepted that include already verified or persistent verification indicators." ::= { appcLuPairOperEntry 6 } -
appcLuPairOperLinkObjId OBJECT-TYPE
-
-
SYNTAX InstancePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the link associated with this partner LU. This value points to the row in the table containing information on the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC MIB module). This object may be NULL if the link is not specified or if a link is not applicable (as for APPN-level nodes)."
-
::= { appcLuPairOperEntry 7 } -
appcLuPairOperParaSessSup OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Active Parallel Sessions Supported.-
-
Indicates whether or not multiple session between the partner LU and its associated local LU are permitted. Parallel session support also indicates that Change Number of Sessions (CNOS) will be used to negotiate session limits between the LUs."
-
::= { appcLuPairOperEntry 8 } -
appcLuPairOperParaSessSupLS OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Active Parallel Sessions Supported - last starting value.-
-
This object represents the initial value proposed by the local LU the last time this capability was negotiated, i.e., when the first session was bound between the local LU and its partner."
-
::= { appcLuPairOperEntry 9 } -
appcLuPairOperState OBJECT-TYPE
SYNTAX INTEGER {
inactive (1),
active (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the current operational state of this LU
pair:
inactive (1) - no active or pending session exists
between the LUs.
active (2) - an active or pending session exists
between the LUs."
::= { appcLuPairOperEntry 10 }
-- *********************************************************************
-- APPC Mode Admin Table
-- Objects in this table contain default or expected configuration
-- values for session modes.
-- Modes that have active sessions appear in the appcModeOperTable.
-- *********************************************************************
appcModeAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcModeAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Mode Table"
::= { appcLu 5 }
appcModeAdminEntry OBJECT-TYPE
SYNTAX AppcModeAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC Mode Information Table."
INDEX { appcModeAdminLocLuName,
appcModeAdminParLuName,
appcModeAdminModeName }
::= { appcModeAdminTable 1 }
AppcModeAdminEntry ::= SEQUENCE {
appcModeAdminLocLuName DisplayString,
appcModeAdminParLuName DisplayString,
appcModeAdminModeName DisplayString,
appcModeAdminCosName DisplayString,
appcModeAdminSessEndTpName DisplayString,
appcModeAdminMaxSessLimit Integer32,
appcModeAdminMinCwinLimit Integer32,
appcModeAdminMinClosLimit Integer32,
appcModeAdminConWinAutoActLmt Integer32,
appcModeAdminRecvPacWinSz Integer32,
appcModeAdminSendPacWinSz Integer32,
appcModeAdminPrefRecvRuSz Integer32,
appcModeAdminPrefSendRuSz Integer32,
appcModeAdminRecvRuSzUpBnd Integer32,
appcModeAdminSendRuSzUpBnd Integer32,
appcModeAdminRecvRuSzLoBnd Integer32,
appcModeAdminSendRuSzLoBnd Integer32,
appcModeAdminSingSessReinit INTEGER,
appcModeAdminCompression INTEGER,
appcModeAdminInBoundCompLevel INTEGER,
appcModeAdminOutBoundCompLevel INTEGER,
appcModeAdminCompRleBeforeLZ INTEGER,
appcModeAdminSyncLvl INTEGER,
appcModeAdminCrypto INTEGER
}
appcModeAdminLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU to which this mode definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.
The reserved value '*ALL' indicates that the mode definition
applies to all local LUs for the SNA node identified by
appcLocalCpName, and not just to a single local LU."
-
::= { appcModeAdminEntry 1 }
appcModeAdminParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the partner LU to which this mode definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
The reserved value '*ALL' indicates that the mode definition applies to all partner LUs for the SNA node identified by appcModeAdminLocLuName, and not just to a single partner LU."
-
::= { appcModeAdminEntry 2 } -
appcModeAdminModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current-
DESCRIPTION
-
"Specifies the mode name. A mode defines the characteristics
for a group of sessions. The mode name can be blank (8
space characters). "
-
::= { appcModeAdminEntry 3 }
appcModeAdminCosName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the class of service (COS) name associated with this mode. If the implementation does not support COS names, a null string is returned." ::= { appcModeAdminEntry 4 }
appcModeAdminSessEndTpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the name of the transaction program (TP) to be invoked when a session using this mode is deactivated or ended. If no such TP is defined, this object is a null string. When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes). " ::= { appcModeAdminEntry 5 }
appcModeAdminMaxSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the maximum value that the local LU is to use,
during CNOS processing, for the session limit. The local LU,
as a target LU, will negotiate a higher session limit it
-
-
-
receives in the CNOS request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value."
-
::= { appcModeAdminEntry 6 } -
appcModeAdminMinCwinLimit OBJECT-TYPE
-
SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the default minimum contention winner sessions limit. Some implementations internally issue a INITIALIZE_SESSION_LIMIT verb when a Mode is created. This value is the parameter used for the CNOS processing of that verb. This parameter is not used when issuing an explicit INITIALIZE_SESSION_LIMIT verb. The equivalent object in appcCnosCommandTable is used." ::= { appcModeAdminEntry 7 }
appcModeAdminMinClosLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the default minimum contention loser sessions limit. Some implementations internally issue a INITIALIZE_SESSION_LIMIT verb when a Mode is created. This value is the parameter used for the CNOS processing of that verb. This is the same as target minimum contention winner sessions. This parameter is not used when issuing an explicit INITIALIZE_SESSION_LIMIT verb. The equivalent object in appcCnosCommandTable is used."
-
::= { appcModeAdminEntry 8 } -
appcModeAdminConWinAutoActLmt OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the limit on the number of contention winner sessions to be automatically activated when the minimum number of contention winner sessions increases (as a result of CNOS processing). The actual number of sessions activated is the lesser of this value and the new minimum number of contention winner sessions. "
-
::= { appcModeAdminEntry 9 } -
appcModeAdminRecvPacWinSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the size of the receive pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether adaptive pacing is supported:
-
-
adaptive pacing No limit on window size
fixed pacing No pacing is supported"
-
::= { appcModeAdminEntry 10 }
appcModeAdminSendPacWinSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the size of the send pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether adaptive pacing is supported:
-
-
adaptive pacing No limit on window size
fixed pacing No pacing is supported"
-
::= { appcModeAdminEntry 11 }
appcModeAdminPrefRecvRuSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the preferred receive RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeAdminRecvRuSzUpBnd and greater than or equal to the value specified in appcModeAdminRecvRuSzLoBnd.
The local LU specifies this value for the receive maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeAdminRecvRuSzUpBnd value or down to the appcModeAdminRecvRuSzLoBnd value."
-
::= { appcModeAdminEntry 12 } -
appcModeAdminPrefSendRuSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the preferred send RU (Request Unit) size of normal- flow requests on the sessions. This value must be less than or equal to the value specified in appcModeAdminSendRuSzUpBnd and greater than or equal to the value specified in appcModeAdminSendRuSzLoBnd.
The local LU specifies this value for the send maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeAdminSendRuSzUpBnd value or down to the appcModeAdminSendRuSzLoBnd value."
-
::= { appcModeAdminEntry 13 } -
appcModeAdminRecvRuSzUpBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the upper bound for the maximum receive RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
-
::= { appcModeAdminEntry 14 }
appcModeAdminSendRuSzUpBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the upper bound for the maximum send RU (Request
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
-
::= { appcModeAdminEntry 15 }
appcModeAdminRecvRuSzLoBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the lower bound for the maximum receive RU (Request
-
-
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
-
::= { appcModeAdminEntry 16 }
appcModeAdminSendRuSzLoBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the lower bound for the maximum send RU (Request
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
-
::= { appcModeAdminEntry 17 }
appcModeAdminSingSessReinit OBJECT-TYPE
-
SYNTAX INTEGER { notApplicable(1), operatorControlled(2), primaryOnly(3), secondaryOnly(4), primaryOrSecondary(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the responsibility for session reinitiation of a single session with the partner LU (when the session goes down). The local LU uses this parameter to specify the session reinitiation responsibility in session activation (SNA BIND) requests and responses. notApplicable - specifies that this parameter has no meaning since the value of appcLuPairAdminParaSessSup is yes. The field in the SNA BIND is reserved (set to zero). operatorControlled - specifies that neither LU will automatically attempt to reinitiate the session. The operator on either side will manually reactivate the session. A contention race (both side reinitiating at the same time) is won by the LU with the lexicographically greater fully- qualified LU name. primaryOnly - specifies that the primary LU will automatically attempt to reinitiate the session. secondaryOnly - specifies that the secondary LU will automatically attempt to reinitiate the session. primaryOrSecondary - specifies that either the primary or the secondary may automatically attempt to reinitiate the session. A contention race is handled the same way as with operatorControlled. " ::= { appcModeAdminEntry 18 }
appcModeAdminCompression OBJECT-TYPE
-
SYNTAX INTEGER { prohibited(1), required(2), negotiable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated." ::= { appcModeAdminEntry 19 }
appcModeAdminInBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcModeAdminCompression for negotiation during session-
-
activation (SNA BIND).
-
none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeAdminEntry 20 } -
appcModeAdminOutBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcModeAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeAdminEntry 21 }
appcModeAdminCompRleBeforeLZ OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used." ::= { appcModeAdminEntry 22 }
appcModeAdminSyncLvl OBJECT-TYPE
-
SYNTAX INTEGER { none(1), noneConfirm(2), noneConfirmSyncPoint(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the sync level support. This value is used for negotiation during session activations (SNA BIND). none - No sync level is supported. noneConfirm - None and Confirm levels supported. noneConfirmSyncPoint - None, Confirm, and Sync Point is supported. " ::= { appcModeAdminEntry 23 }
appcModeAdminCrypto OBJECT-TYPE
-
-
SYNTAX INTEGER {
-
notSupported(1),
mandatory(2),
selective(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether session-level cryptography is supported.
This value is used for negotiation during session activations
(SNA BIND).
notSupported - Specifies session-level cryptography
is not to be used.
mandatory - Specifies session-level cryptography
must be used.
selective - Specifies session-level cryptography
is required just on selected requests
flowing on the sessions."
::= { appcModeAdminEntry 24 }
-- *********************************************************************
-- APPC Mode Oper Table
-- Objects in this table contain current operational values, such
-- as state values or negotiated parameters, for session modes.
--
-- *********************************************************************
appcModeOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcModeOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Operational APPC Mode Information. Two entries are present in
the table when both LUs in a pair are local."
::= { appcLu 6 }
appcModeOperEntry OBJECT-TYPE
-
-
SYNTAX AppcModeOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry of APPC mode operational information table. This entry does not augment the appcModeAdminEntry, but reflects an actual operational mode for a given local LU - partner LU pair."
INDEX { appcModeOperLocLuName,
-
-
appcModeOperParLuName,
appcModeOperModeName }
-
-
::= { appcModeOperTable 1 } -
AppcModeOperEntry ::= SEQUENCE {
-
appcModeOperLocLuName DisplayString, appcModeOperParLuName DisplayString, appcModeOperModeName DisplayString, appcModeOperCosName DisplayString, appcModeOperSessEndTpName DisplayString, appcModeOperSessLimit Integer32, appcModeOperMaxSessLimit Integer32, appcModeOperMinCwinLimit Integer32, appcModeOperMinClosLimit Integer32, appcModeOperConWinAutoActLmt Integer32, appcModeOperRecvPacWinSz Integer32, appcModeOperSendPacWinSz Integer32, appcModeOperPrefRecvRuSz Integer32, appcModeOperPrefSendRuSz Integer32, appcModeOperRecvRuSzUpBnd Integer32, appcModeOperSendRuSzUpBnd Integer32, appcModeOperRecvRuSzLoBnd Integer32, appcModeOperSendRuSzLoBnd Integer32, appcModeOperSingSessReinit INTEGER, appcModeOperCompression INTEGER, appcModeOperInBoundCompLevel INTEGER, appcModeOperOutBoundCompLevel INTEGER, appcModeOperCompRleBeforeLZ INTEGER, appcModeOperSyncLvl INTEGER, appcModeOperCrypto INTEGER, appcModeOperSyncLvlLastStart INTEGER, appcModeOperCryptoLastStart INTEGER, appcModeOperCNOSNeg INTEGER, appcModeOperActCwin Gauge32, appcModeOperActClos Gauge32, appcModeOperPndCwin Gauge32, appcModeOperPndClos Gauge32, appcModeOperPtmCwin Gauge32, appcModeOperPtmClos Gauge32, appcModeOperDrainSelf INTEGER, appcModeOperDrainPart INTEGER }
appcModeOperLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.
If this object has the same value as appcLluOperName,
then the two entries being indexed apply to the same
resource (specifically, to the same local LU)."
-
::= { appcModeOperEntry 1 }
appcModeOperParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU)."
-
::= { appcModeOperEntry 2 } -
appcModeOperModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). " ::= { appcModeOperEntry 3 }
appcModeOperCosName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the class of service (COS) name associated with this mode. If the implementation does not support COS names, a zero-length string is returned." ::= { appcModeOperEntry 4 }
appcModeOperSessEndTpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION-
-
"Specifies the name of the transaction program (TP) to be invoked when a session using this mode is deactivated or ended. If the name is NULL, no transaction program is invoked. When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes)."
-
::= { appcModeOperEntry 5 } -
appcModeOperSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the current session limit of this mode as negotiated through APPC CNOS (Change Number of Sessions) processing. Identifies the total number of sessions that can be established between the local and partner LU using this mode."
-
::= { appcModeOperEntry 6 } -
appcModeOperMaxSessLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the maximum value that the local LU is to use, during CNOS processing, for the session limit. The local LU, as a target LU, will negotiate a higher session limit it receives in the CNOS request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value."
-
::= { appcModeOperEntry 7 } -
appcModeOperMinCwinLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the minimum contention winner sessions limit that
was negotiated via CNOS processing."
-
::= { appcModeOperEntry 8 } -
appcModeOperMinClosLimit OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the minimum contention loser sessions limit that
was negotiated via CNOS processing. This is the same as
target minimum contention winner sessions."
-
::= { appcModeOperEntry 9 }
appcModeOperConWinAutoActLmt OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the limit on the number of contention winner sessions to be automatically activated when the minimum number of contention winner sessions increases (as a result of CNOS processing). The actual number of sessions activated is the lesser of this value and the new minimum number of contention winner sessions. "
-
::= { appcModeOperEntry 10 } -
appcModeOperRecvPacWinSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the size of the receive pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether adaptive pacing is supported:
-
-
adaptive pacing - No limit on window size
fixed pacing - No pacing is supported"
-
::= { appcModeOperEntry 11 }
appcModeOperSendPacWinSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-onlySTATUS current
DESCRIPTION-
"Specifies the size of the send pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether adaptive pacing is supported:
-
-
adaptive pacing No limit on window size
fixed pacing No pacing is supported"
-
::= { appcModeOperEntry 12 }
appcModeOperPrefRecvRuSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the preferred receive RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeOperRecvRuSzUpBnd and greater than or equal to the value specified in appcModeOperRecvRuSzLoBnd.
The local LU specifies this value for the receive maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeOperRecvRuSzUpBnd value or down to the appcModeOperRecvRuSzLoBnd value."
-
::= { appcModeOperEntry 13 } -
appcModeOperPrefSendRuSz OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the preferred send RU (Request Unit) size of normal- flow requests on the sessions. This value must be less than or equal to the value specified in appcModeOperSendRuSzUpBnd and greater than or equal to the value specified in appcModeOperSendRuSzLoBnd.
The local LU specifies this value for the send maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeOperSendRuSzUpBnd value or down to the appcModeOperSendRuSzLoBnd value."
-
::= { appcModeOperEntry 14 } -
appcModeOperRecvRuSzUpBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the upper bound for the maximum receive RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
-
::= { appcModeOperEntry 15 }
appcModeOperSendRuSzUpBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the upper bound for the maximum send RU (Request
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
-
::= { appcModeOperEntry 16 }
appcModeOperRecvRuSzLoBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the lower bound for the maximum receive RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
-
::= { appcModeOperEntry 17 }
appcModeOperSendRuSzLoBnd OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the lower bound for the maximum send RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
-
::= { appcModeOperEntry 18 }
appcModeOperSingSessReinit OBJECT-TYPE
-
-
SYNTAX INTEGER {
-
-
-
-
notApplicable(1),
operatorControlled(2),
-
-
-
primaryOnly(3), secondaryOnly(4), primaryOrSecondary(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the responsibility for session reinitiation of a single session with the partner LU (when the session goes down). The local LU uses this parameter to specify the session reinitiation responsibility in session activation (SNA BIND) requests and responses. notApplicable - specifies that this parameter has no meaning since the value of appcLuPairOperParaSessSup is yes. The field in the SNA BIND is reserved (set to zero). operatorControlled - specifies that neither LU will automatically attempt to reinitiate the session. The operator on either side will manually reactivate the session. A contention race (both side reinitiating at the same time) is won by the LU with the lexicographically greater fully- qualified LU name. primaryOnly - specifies that the primary LU will automatically attempt to reinitiate the session. secondaryOnly - specifies that the secondary LU will automatically attempt to reinitiate the session. primaryOrSecondary - specifies that either the primary or the secondary may automatically attempt to reinitiate the session. A contention race is handled the same way as with operatorControlled. " ::= { appcModeOperEntry 19 } -
appcModeOperCompression OBJECT-TYPE
-
SYNTAX INTEGER { prohibited(1), required(2), negotiable(3) } MAX-ACCESS read-only-
STATUS current
DESCRIPTION-
"Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND).
-
prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LUs. The level of compression is also negotiated." ::= { appcModeOperEntry 20 } -
appcModeOperInBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcModeOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeOperEntry 21 }
appcModeOperOutBoundCompLevel OBJECT-TYPE
-
SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcModeOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeOperEntry 22 }
appcModeOperCompRleBeforeLZ OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used." ::= { appcModeOperEntry 23 }
appcModeOperSyncLvl OBJECT-TYPE
-
SYNTAX INTEGER { none(1), noneConfirm(2), noneConfirmSyncPoint(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the sync level support for sessions involving this LU pair and mode name. none - No sync level is supported. noneConfirm - None and Confirm level supported. noneConfirmSyncPoint - None, Confirm and Sync Point is supported. " ::= { appcModeOperEntry 24 }
appcModeOperCrypto OBJECT-TYPE
-
SYNTAX INTEGER { notSupported(1), mandatory(2), selective(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether session-level cryptography is supported for sessions involving this LU pair and mode name. notSupported - Specifies session-level cryptography is not being used. mandatory - Specifies session-level cryptography in being used on all requests flowing on the sessions. selective - Specifies session-level cryptography is required just on selected requests flowing on the sessions." ::= { appcModeOperEntry 25 }
appcModeOperSyncLvlLastStart OBJECT-TYPE
-
-
SYNTAX INTEGER {
-
-
-
-
none(1),
-
-
-
noneConfirm(2), noneConfirmSyncPoint(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the sync level support. This value represents the initial value proposed by the local LU the last time this capability was negotiated, i.e., when the first session was bound between the local LU and its partner. none - No sync level is supported. noneConfirm - None and Confirm level supported. noneConfirmSyncPoint - None, Confirm and Sync Point is supported. " ::= { appcModeOperEntry 26 } -
appcModeOperCryptoLastStart OBJECT-TYPE
-
SYNTAX INTEGER { notSupported(1), mandatory(2), selective(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether session-level cryptography is supported. This value represents the initial value proposed by the local LU the last time this capability was negotiated, i.e., when the first session was bound between the local LU and its partner. notSupported - Specifies session-level cryptography is not to be used. mandatory - Specifies session-level cryptography must be used. selective - Specifies session-level cryptography is required just on selected requests flowing on the sessions." ::= { appcModeOperEntry 27 }
appcModeOperCNOSNeg OBJECT-TYPE
-
-
SYNTAX INTEGER {
no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether CNOS negotiation is in process. CNOS negotiation is used to set or change the various session limits for a mode." ::= { appcModeOperEntry 28 } -
appcModeOperActCwin OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the number of active contention winner sessions."
-
::= { appcModeOperEntry 29 }
appcModeOperActClos OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the number of active contention loser sessions."
-
::= { appcModeOperEntry 30 }
appcModeOperPndCwin OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the number of contention winner sessions that are
-
pending activation." ::= { appcModeOperEntry 31 } -
appcModeOperPndClos OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the number of contention loser sessions that are
-
pending activation." ::= { appcModeOperEntry 32 } -
appcModeOperPtmCwin OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the number of contention winner sessions that are
-
pending termination." ::= { appcModeOperEntry 33 } -
appcModeOperPtmClos OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Specifies the number of contention loser sessions that are
-
pending termination." ::= { appcModeOperEntry 34 } -
appcModeOperDrainSelf OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the local LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the local LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stopped or BIS protocol). " ::= { appcModeOperEntry 35 }
appcModeOperDrainPart OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the partner LU is draining its conversations for this mode. When a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the partner LU could be set to process all queued conversations before deactivating all of the-
-
sessions (using the SNA Bracket Initiation Stop or BIS protocol). "
-
-
::= { appcModeOperEntry 36 }
-- *********************************************************************
-- APPC TP Admin Table
-- Objects in this table contain default or expected configuration
-- values for remotely attachable transaction programs.
-- *********************************************************************
appcTpAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcTpAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Local TP Table"
::= { appcTp 1 }
appcTpAdminEntry OBJECT-TYPE
-
-
SYNTAX AppcTpAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry of APPC Local TP Information Table."
INDEX { appcTpAdminLocLuName,
-
-
appcTpAdminTpName }
::= { appcTpAdminTable 1 }
AppcTpAdminEntry ::= SEQUENCE {
appcTpAdminLocLuName DisplayString,
appcTpAdminTpName DisplayString,
appcTpAdminFileSpec DisplayString,
appcTpAdminStartParm DisplayString,
appcTpAdminTpOperation INTEGER,
appcTpAdminInAttachTimeout Integer32,
appcTpAdminRcvAllocTimeout Integer32,
appcTpAdminSyncLvl INTEGER,
appcTpAdminInstLmt Integer32,
appcTpAdminStatus INTEGER,
appcTpAdminLongRun INTEGER,
appcTpAdminConvType INTEGER,
appcTpAdminConvDuplex INTEGER,
appcTpAdminConvSecReq INTEGER,
appcTpAdminVerPip INTEGER,
appcTpAdminPipSubNum Integer32
}
appcTpAdminLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU to which this TP definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
The reserved value '*ALL' indicates that the TP definition applies to all local LUs, and not just to a single local LU."
-
::= { appcTpAdminEntry 1 } -
appcTpAdminTpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The local transaction program name. This name is sent on an ATTACH remote allocation request.-
-
When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes)."
-
::= { appcTpAdminEntry 2 } -
appcTpAdminFileSpec OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "The local file specification of the transaction program. May be a zero-length string if not applicable." ::= { appcTpAdminEntry 3 }
appcTpAdminStartParm OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A parameter string passed to the transaction program when it is started. May be a zero-length string if not supported. " ::= { appcTpAdminEntry 4 }
appcTpAdminTpOperation OBJECT-TYPE
-
SYNTAX INTEGER { other(1), queuedOperatorStarted(2), queuedOperatorPreloaded(3), queuedAmStarted(4), nonqueuedAmStarted(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies how the program will be started. other - Specifies that the program operation is none of the methods specified. It may be a product-specific method.-
-
-
queuedOperatorStarted - Specifies that one version of the
-
-
program will be run at a time. If an incoming attach arrives and the program has not been started yet, APPC will issue a message to the operator to start the specified program. Subsequent attaches that arrive while the program is active will be queued.
-
queuedOperatorPreloaded - Specifies that one version of the
-
-
program will be run at a time. If an incoming attach arrives and the program has not been started yet, the Attach will be rejected. The APPC attach manager determines that a TP has started upon reception of an APPC RECEIVE_ALLOCATE verb, or a CPI-C Accept_Conversation (CMACCP) or Specify_Local_TP_Name (CMSLTP) call. No message is sent to the operator. Subsequent attaches that arrive while the program is active are queued.
-
queuedAmStarted - Specifies that one version of the
-
-
program will be run at a time and will be started by the APPC attach manager. Subsequent attaches that arrive while the program is active will be queued.
-
nonqueuedAmStarted - Specifies that multiple copies of the
-
-
program will be run at a time and will be started by the APPC attach manager."
-
-
-
::= { appcTpAdminEntry 5 } -
appcTpAdminInAttachTimeout OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"This object specifies the number of seconds incoming attaches will be queued waiting for an APPC program to issue a RECEIVE_ALLOCATE verb or for a CPI-C program to issue an Accept_Conversation (CMACCP) call. This parameter is meaningful only when appcTpAdminTpOperation has one of the following values:
-
-
-
queuedOperatorStarted
queuedOperatorPreloaded
queuedAmStarted
-
-
-
-
-
A value of zero indicates that there is no timeout."
-
::= { appcTpAdminEntry 6 }
appcTpAdminRcvAllocTimeout OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"This object specifies the number of seconds an APPC program's RECEIVE_ALLOCATE verb or a CPI-C program's Accept_Conversation (CMACCP) call will wait for an incoming attach to arrive.
-
-
A value of zero indicates that there is no timeout."
-
::= { appcTpAdminEntry 7 }
appcTpAdminSyncLvl OBJECT-TYPE
-
-
SYNTAX INTEGER {
none(1), confirm(2), noneAndConfirm(3), syncpoint(4), noneAndSyncpoint(5), confirmAndSyncpoint(6), all(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the synchronization level or levels that the transaction program supports. The levels are defined as follows: none - allocation requests indicating a synchronization level of none are allowed to start the program. confirm - allocation requests indicating a synchronization level of confirm are allowed to start the program. syncpoint - allocation requests indicating a synchronization level of sync point are allowed to start the program." ::= { appcTpAdminEntry 8 } -
appcTpAdminInstLmt OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The maximum number of concurrent instances of this transaction
program that will be supported for a local LU. A value of zero indicates that there is no limit."
-
::= { appcTpAdminEntry 9 } -
appcTpAdminStatus OBJECT-TYPE
-
SYNTAX INTEGER { enabled(1), tempDisabled(2), permDisabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of the TP relative to starting execution when the local LU receives an allocation (ATTACH) request naming this program. enabled - the local LU can start the program. tempDisabled - the local LU cannot start the program. The local LU rejects the request with an indication that the TP is not available but retry is possible. permDisabled - the local LU cannot start the program. The local LU rejects the request with an indication that the TP is not available and retry is not possible." ::= { appcTpAdminEntry 10 }
appcTpAdminLongRun OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this is a long-running transaction program (i.e., one that stays around even after the conversation goes away)." ::= { appcTpAdminEntry 11 }
appcTpAdminConvType OBJECT-TYPE
-
SYNTAX INTEGER { basic(1), mapped(2), basicOrMapped(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the conversation type (basic or mapped) that will be used by the TP. This value is verified upon receipt of an incoming attach. The acceptable values are: basic - Indicates that this transaction program supports basic conversations. mapped - Indicates that this transaction program supports mapped conversations.-
-
-
-
basicOrMapped - Indicates that this transaction program
-
-
-
-
supports both basic and mapped conversations."
-
-
-
-
-
-
::= { appcTpAdminEntry 12 } -
appcTpAdminConvDuplex OBJECT-TYPE
-
SYNTAX INTEGER { half(1), full(2), halfOrFull(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the conversation duplex type (half or full) that will be used by the TP. This value is verified upon receipt of an incoming attach. The acceptable values are: half - Indicates that this transaction program supports half duplex conversations. full - Indicates that this transaction program supports full duplex conversations.-
-
-
-
halfOrFull - Indicates that this transaction program
-
-
-
supports either half or full duplex conversations."
-
-
-
-
-
::= { appcTpAdminEntry 13 } -
appcTpAdminConvSecReq OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether conversation-level security information is required on incoming attaches designating this TP name. Conversation-level security verification is always performed on those requests that include security information.-
-
-
-
yes - Indicates that conversation-level security
-
information is required. ATTACHs designating the transaction program must carry a user_id and either a password or an already verified indicator.
no - Indicates that no security information is
-
required. ATTACHs designating the transaction program can omit or include security information."
-
-
-
::= { appcTpAdminEntry 14 } -
appcTpAdminVerPip OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the number of PIP (Program Initialization Parameters) subfields should be verified against the number expected (appcTpAdminPipSubNum)." ::= { appcTpAdminEntry 15 }
appcTpAdminPipSubNum OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"Specifies the number of PIP subfields expected by the TP."
::= { appcTpAdminEntry 16 }
-- *********************************************************************
-- APPC Active Session Table
-- ---------------------------------------------------------------------
-- This table contains information about active APPC sessions.
-- *********************************************************************
appcActSessTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcActSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of active APPC sessions. Two entries are present in the
table when both session partners are local."
::= { appcSession 1 }
appcActSessEntry OBJECT-TYPE
-
-
SYNTAX AppcActSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry of APPC Session Information Table. Indexed by LU pair and integer-valued session index."
INDEX { appcActSessLocLuName,
-
-
appcActSessParLuName,
appcActSessIndex }
-
-
-
::= { appcActSessTable 1 }
AppcActSessEntry ::= SEQUENCE {
appcActSessLocLuName DisplayString,
appcActSessParLuName DisplayString,
appcActSessIndex Integer32,
appcActSessPcidCpName DisplayString,
appcActSessPcid OCTET STRING,
appcActSessPluIndicator INTEGER,
appcActSessModeName DisplayString,
appcActSessCosName DisplayString,
appcActSessTransPriority INTEGER,
appcActSessEnhanceSecSup INTEGER,
appcActSessSendPacingType INTEGER,
appcActSessSendRpc Gauge32,
appcActSessSendNxWndwSize Gauge32,
appcActSessRecvPacingType INTEGER,
appcActSessRecvRpc Gauge32,
appcActSessRecvNxWndwSize Gauge32,
appcActSessRscv OCTET STRING,
appcActSessInUse INTEGER,
appcActSessMaxSndRuSize INTEGER,
appcActSessMaxRcvRuSize INTEGER,
appcActSessSndPacingSize INTEGER,
appcActSessRcvPacingSize INTEGER,
appcActSessOperState INTEGER,
appcActSessUpTime TimeTicks,
appcActSessRtpNceId OCTET STRING,
appcActSessRtpTcid OCTET STRING,
appcActSessLinkIndex InstancePointer
}
appcActSessLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the name of the local LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is-
-
present.
If this object has the same value as appcLluOperName, then the two entries being indexed apply to the same resource (specifically, to the same local LU)."
-
::= { appcActSessEntry 1 } -
appcActSessParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the name of the partner LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU)."
-
::= { appcActSessEntry 2 } -
appcActSessIndex OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"This value identifies the index of the session, which is unique for this LU pair. It is recommended that an Agent not reuse the index of a deactivated session for a significant period of time (e.g., one week)."
-
::= { appcActSessEntry 3 } -
appcActSessPcidCpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0 | 3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network-qualified CP name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name. A null string indicates that the value is unknown." ::= { appcActSessEntry 4 }
appcActSessPcid OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0|8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The procedure correlation identifier (PCID) of a session. It is an 8-octet value assigned by the control point providing session services for the primary LU. A null string indicates that the value is unknown." ::= { appcActSessEntry 5 }
appcActSessPluIndicator OBJECT-TYPE
-
SYNTAX INTEGER { localLuIsPlu(1), partnerLuIsPlu(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates which LU is the PLU for this session. For independent LUs, the PLU (primary LU) is the one that initiated the session (sent BIND), while the SLU (secondary LU) is the one that accepted the session initiation (received BIND).
The 'local' LU is the one identified by appcLluOperName.
-
-
-
The 'partner' LU is the one identified by appcLuPairOperParLuName."
-
::= { appcActSessEntry 6 } -
appcActSessModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The mode name used for this session." ::= { appcActSessEntry 7 }
appcActSessCosName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION
"The Class of Service (COS) name used for this session.
A null string indicates that the value is unknown."
-
::= { appcActSessEntry 8 }
appcActSessTransPriority OBJECT-TYPE
-
SYNTAX INTEGER { unknown(1), low(2), medium(3), high(4), network(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission priority of this session. 1 = unknown priority 2 = low priority 3 = medium priority 4 = high priority 5 = network priority " ::= { appcActSessEntry 9 }
appcActSessEnhanceSecSup OBJECT-TYPE
-
SYNTAX INTEGER { none(1), level1(2), level2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enhanced security supported. Indicates the level of enhanced security support: 1 = none 2 = level 1 3 = level 2 " ::= { appcActSessEntry 10 }
appcActSessSendPacingType OBJECT-TYPE
-
-
SYNTAX INTEGER {
-
-
-
-
none(1),
-
-
-
fixed(2), adaptive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of pacing being used for sending data." ::= { appcActSessEntry 11 } -
appcActSessSendRpc OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The send residual pace count. This represents the number of MUs that can still be sent in the current session window."
-
::= { appcActSessEntry 12 } -
appcActSessSendNxWndwSize OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The size of the next window which will be used to send data."
-
::= { appcActSessEntry 13 } -
appcActSessRecvPacingType OBJECT-TYPE
-
SYNTAX INTEGER { none(1), fixed(2), adaptive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of pacing being used for receiving data." ::= { appcActSessEntry 14 }
appcActSessRecvRpc OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The receive residual pace count. This represents the number of MUs that can still be received in the current session window."
-
::= { appcActSessEntry 15 } -
appcActSessRecvNxWndwSize OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The size of the next window which will be used to receive data."
-
-
::= { appcActSessEntry 16 }
appcActSessRscv OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The route selection control vector (RSCV CV2B) used for this
session. It is present for APPN-level implementations.
LEN-level implementations will return a null string. The
internal format of this vector is described in SNA Formats.
This object contains an uninterpreted copy of the control
vector (including the length and key fields)."
::= { appcActSessEntry 17 }
appcActSessInUse OBJECT-TYPE
-
SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the session is currently in use (i.e., in bracket with a conversation)." ::= { appcActSessEntry 18 }
appcActSessMaxSndRuSize OBJECT-TYPE
-
SYNTAX INTEGER (1..8192) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum RU size used on this session for sending RUs." ::= { appcActSessEntry 19 }
appcActSessMaxRcvRuSize OBJECT-TYPE
-
SYNTAX INTEGER (1..8192) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum RU size used on this session for receiving RUs." ::= { appcActSessEntry 20 }
appcActSessSndPacingSize OBJECT-TYPE
-
SYNTAX INTEGER (1..63) MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the send pacing window on this session." ::= { appcActSessEntry 21 }
appcActSessRcvPacingSize OBJECT-TYPE
-
SYNTAX INTEGER (1..63) MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the receive pacing window on this session." ::= { appcActSessEntry 22 }
appcActSessOperState OBJECT-TYPE
-
SYNTAX INTEGER { unbound (1), pendingBind (2), bound (3), pendingUnbind (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The value indicates the current operational state of the session.
'unbound (1)' - session has been unbound;
in this state it will be removed from the
session table by the Agent.
-
-
-
-
-
'pendingBind (2)' - this state has different
-
meanings for dependent and independent LUs; for dependent LU - waiting for BIND from the host, for independent LU - waiting for BIND response. When a session enters this state, the corresponding entry in the session table is created by the Agent.
'bound (3)' - session has been successfully bound.
'pendingUnbind (4)' - session enters this state
-
when an UNBIND is sent and before the rsp(UNBIND) is received.
-
Session deactivation:
-
-
If a session is in the operational state
'bound (3)' then setting the value of this
object to 'unbound (1)' will initiate the session shutdown.If a session is in the operational state 'pendingBind (2)' then setting the value of this object to 'unbound (1)' will initiate the session shutdown.
If a session is in the operational state 'pendingUnbind (4)' for an abnormally long period of time (e.g., three minutes) then setting the value of this object to 'unbound (1)' will change the session operational state to 'unbound (1)'. "
-
-
-
::= { appcActSessEntry 23 } -
appcActSessUpTime OBJECT-TYPE
-
-
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The length of time the session has been active, measured in hundredths of a second."
-
::= { appcActSessEntry 24 } -
appcActSessRtpNceId OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The local HPR Network Connection Endpoint of the session." ::= { appcActSessEntry 25 }
appcActSessRtpTcid OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0|8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The local RTP connection TCID of the session." ::= { appcActSessEntry 26 }
appcActSessLinkIndex OBJECT-TYPE
-
-
SYNTAX InstancePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"This value identifies the link over which the session passes. This value points to the row in the table containing information on the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC MIB module). This object may be NULL if the link is not specified or if a link is not applicable (as for APPN-level nodes)."
-
-
::= { appcActSessEntry 27 }
-- ***************************************************************
-- The following table contains session statistics for APPC sessions.
-- ***************************************************************
appcSessStatsTable OBJECT-TYPE
-
-
SYNTAX SEQUENCE OF AppcSessStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"This table contains dynamic statistical information relating to active APPC sessions. The entries in this table cannot be created by a Management Station. Two entries are present in the table when both session partners are local. This table is populated only when the value of appcCntrlOperStat is 'active'."
-
::= { appcSession 2 } -
appcSessStatsEntry OBJECT-TYPE
-
-
SYNTAX AppcSessStatsEntry
MAX-ACCESS not-accessible
STATUS currentDESCRIPTION
-
"Contains statistics information for an APPC session. Each entry is created by the Agent. Objects in this table have read-only access. Each session from appcActSessTable has one entry in this table."
INDEX { appcSessStatsLocLuName,
-
-
appcSessStatsParLuName,
appcSessStatsSessIndex }
-
::= { appcSessStatsTable 1 } -
AppcSessStatsEntry ::= SEQUENCE {
-
appcSessStatsLocLuName DisplayString, appcSessStatsParLuName DisplayString, appcSessStatsSessIndex Integer32, appcSessStatsSentFmdBytes Counter32, appcSessStatsSentNonFmdBytes Counter32, appcSessStatsRcvdFmdBytes Counter32, appcSessStatsRcvdNonFmdBytes Counter32, appcSessStatsSentFmdRus Counter32, appcSessStatsSentNonFmdRus Counter32, appcSessStatsRcvdFmdRus Counter32, appcSessStatsRcvdNonFmdRus Counter32, appcSessStatsCtrUpTime TimeTicks }
appcSessStatsLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the name of the local LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
If this object has the same value as appcLluOperName, then the two entries being indexed apply to the same resource (specifically, to the same local LU)."
-
::= { appcSessStatsEntry 1 } -
appcSessStatsParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION-
-
"Specifies the name of the partner LU for the session. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.
If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU)."
-
::= { appcSessStatsEntry 2 } -
appcSessStatsSessIndex OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"This value identifies the index of the session, which is unique for this LU pair. It is recommended that an Agent not reuse the index of a deactivated session for a significant period of time (e.g., one week).
If this object has the same value as appcActSessIndex for the same LU pair, then the two entries being indexed apply to the same resource (specifically, to the same session)."
-
::= { appcSessStatsEntry 3 } -
appcSessStatsSentFmdBytes OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of function management data (FMD) bytes sent by the local LU."
-
::= { appcSessStatsEntry 4 } -
appcSessStatsSentNonFmdBytes OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of non-function management data (non-FMD) bytes sent by the local LU."
-
::= { appcSessStatsEntry 5 } -
appcSessStatsRcvdFmdBytes OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of function management data (FMD) bytes received by the local LU."
-
::= { appcSessStatsEntry 6 } -
appcSessStatsRcvdNonFmdBytes OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of non-function management data (non-FMD) bytes received by the local LU."
-
::= { appcSessStatsEntry 7 } -
appcSessStatsSentFmdRus OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of function management data (FMD) RUs sent by the local LU."
-
::= { appcSessStatsEntry 8 } -
appcSessStatsSentNonFmdRus OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of non-function management data (non-FMD) RUs sent by the local LU."
-
::= { appcSessStatsEntry 9 } -
appcSessStatsRcvdFmdRus OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of function management data (FMD) RUs received by the local LU."
-
::= { appcSessStatsEntry 10 } -
appcSessStatsRcvdNonFmdRus OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of non-function management data (non-FMD) RUs received by the local LU."
-
::= { appcSessStatsEntry 11 } -
appcSessStatsCtrUpTime OBJECT-TYPE
-
-
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The length of time the counters for this session have been active, measured in hundredths of a second."
-
-
::= { appcSessStatsEntry 12 }
-- *********************************************************************
-- APPC Historical Session Table
-- ---------------------------------------------------------------------
-- This table contains historical information about APPC sessions that
-- terminated abnormally. It is an implementation choice how long to
-- retain information on a given session.
-- *********************************************************************
appcHistSessTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcHistSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of historical information about APPC sessions that
terminated abnormally. Two entries may be present in the table
when both session partners are local. It is an implementation
choice how long to retain information about a given session."
::= { appcSession 3 }
appcHistSessEntry OBJECT-TYPE
-
-
SYNTAX AppcHistSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry of APPC Session History Table. This table is indexed by an integer which is continuously incremented until it eventually wraps."
INDEX
-
-
{ appcHistSessIndex }
::= { appcHistSessTable 1 }
AppcHistSessEntry ::= SEQUENCE {
appcHistSessIndex INTEGER,
appcHistSessTime DateAndTime,
appcHistSessType INTEGER,
appcHistSessLocLuName DisplayString,
appcHistSessParLuName DisplayString,
appcHistSessModeName DisplayString,
appcHistSessUnbindType OCTET STRING,
appcHistSessSenseData SnaSenseData,
appcHistSessComponentId DisplayString,
appcHistSessDetectModule DisplayString
}
appcHistSessIndex OBJECT-TYPE
-
SYNTAX INTEGER (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table index. The value of the index begins at zero and is incremented up to a maximum value of 2**31-1 (2,147,483,647) before wrapping." ::= { appcHistSessEntry 1 }
appcHistSessTime OBJECT-TYPE
-
-
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The time at which the session was either terminated or
failed to be established."
-
::= { appcHistSessEntry 2 } -
appcHistSessType OBJECT-TYPE
-
-
SYNTAX INTEGER {
recvNegBindRsp(1), sendNegBindRsp(2), sessActRejected(3), unbindSent(4), unbindReceived(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of event that caused the entry to be made: recvNegBindRsp - Received a negative bind response from the partner LU. sendNegBindRsp - Sent a negative bind response to the partner LU. sessActRejected - Session activation rejected by the partner LU. unbindSent - Unbind sent to the partner LU. unbindReceived - Unbind received from the partner LU. -
These event types correspond to the five SNA/MS Alerts
LU62001 through LU62005, documented in the SNA Management
Services Reference."
-
::= { appcHistSessEntry 3 }
appcHistSessLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network-qualified local LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcHistSessEntry 4 }
appcHistSessParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network-qualified partner LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcHistSessEntry 5 }
appcHistSessModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The mode name of the session." ::= { appcHistSessEntry 6 }
appcHistSessUnbindType OBJECT-TYPE
-
-
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"The type of unbind which terminated the session. This
value is consists of one (1) octet; and its meaning
is defined in SNA Formats."
-
::= { appcHistSessEntry 7 }
appcHistSessSenseData OBJECT-TYPE
-
-
SYNTAX SnaSenseData
MAX-ACCESS read-only
STATUS current
DESCRIPTION
-
"The sense data associated with the termination of the
session, taken from the negative BIND response or UNBIND
request."
-
::= { appcHistSessEntry 8 }
appcHistSessComponentId OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The implementation-specific name of the component which detected the problem." ::= { appcHistSessEntry 9 }
appcHistSessDetectModule OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The implementation-specific name of the module which
detected the problem."
::= { appcHistSessEntry 10 }
-- *********************************************************************
-- APPC Session RTP Connection Table
-- ---------------------------------------------------------------------
-- This table contains information on APPC sessions that are being
-- transported on RTP connections by High Performance Routing (HPR).
-- *********************************************************************
appcSessRtpTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcSessRtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table indicating how many APPC sessions terminating in this
node are transported by each RTP connection."
::= { appcSession 4 }
appcSessRtpEntry OBJECT-TYPE
-
-
SYNTAX AppcSessRtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry of APPC session RTP table."
INDEX { appcSessRtpNceId,
-
appcSessRtpTcid } ::= { appcSessRtpTable 1 } -
AppcSessRtpEntry ::= SEQUENCE {
-
appcSessRtpNceId OCTET STRING, appcSessRtpTcid OCTET STRING, appcSessRtpSessions Gauge32 }
appcSessRtpNceId OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The local Network Connection Endpoint of the RTP connection." ::= { appcSessRtpEntry 1 }
appcSessRtpTcid OBJECT-TYPE
-
-
SYNTAX OCTET STRING (SIZE (8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"The local TCID of the RTP connection."
-
::= { appcSessRtpEntry 2 } -
appcSessRtpSessions OBJECT-TYPE
-
-
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The number of APPC sessions terminating in this node that are using this RTP connection."
-
-
::= { appcSessRtpEntry 3 }
-- *********************************************************************
-- APPC Active Conversation Table
-- This table contains information about active APPC conversations.
-- *********************************************************************
appcActiveConvTable OBJECT-TYPE
-
-
SYNTAX SEQUENCE OF AppcActiveConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Table of information about active APPC Conversations. In this context 'active' means that a conversation is currently associated with a particular session. Two entries are present in the table when both LUs for the session are local."
-
::= { appcConversation 1 } -
appcActiveConvEntry OBJECT-TYPE
-
-
SYNTAX AppcActiveConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
-
"Entry representing one active APPC Conversation."
-
-
INDEX { appcActiveConvLocLuName,
-
-
appcActiveConvParLuName,
appcActiveConvSessIndex }
-
-
::= { appcActiveConvTable 1}
AppcActiveConvEntry ::= SEQUENCE {
appcActiveConvLocLuName DisplayString,
appcActiveConvParLuName DisplayString,
appcActiveConvSessIndex Integer32,
appcActiveConvId OCTET STRING,
appcActiveConvState INTEGER,
appcActiveConvType INTEGER,
appcActiveConvCorrelator OCTET STRING,
appcActiveConvSyncLvl INTEGER,
appcActiveConvSource INTEGER,
appcActiveConvDuplex INTEGER,
appcActiveConvUpTime TimeTicks,
appcActiveConvSendBytes Counter32,
appcActiveConvRcvBytes Counter32,
appcActiveConvUserid DisplayString,
appcActiveConvPcidNauName DisplayString,
appcActiveConvPcid OCTET STRING,
appcActiveConvModeName DisplayString,
appcActiveConvLuwIdName DisplayString,
appcActiveConvLuwIdInstance OCTET STRING,
appcActiveConvLuwIdSequence OCTET STRING,
appcActiveConvTpName DisplayString
}
appcActiveConvLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU for the conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.
If this object has the same value as appcLluOperName,
then the two entries being indexed apply to the same
resource (specifically, to the same local LU)."
-
::= { appcActiveConvEntry 1 }
appcActiveConvParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the partner LU for the conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
If this object has the same value as appcLuPairOperParLuName, then the two entries being indexed apply to the same resource (specifically, to the same partner LU)."
-
::= { appcActiveConvEntry 2 } -
appcActiveConvSessIndex OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Index of entry in appcActSessTable that is associated with this conversation. If this object has the same value as appcActSessIndex for the same LU pair, then the two entries being indexed apply to the same resource (specifically, to the same session)."
-
::= { appcActiveConvEntry 3 } -
appcActiveConvId OBJECT-TYPE
-
-
SYNTAX OCTET STRING (SIZE (4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The 4-byte ID of the conversation."
-
::= { appcActiveConvEntry 4 } -
appcActiveConvState OBJECT-TYPE
-
-
SYNTAX INTEGER {
reset(1), send(2), receive(3), confirm(4), confirmSend(5), confirmDealloc(6), pendingDeallocate(7), pendingPost(8), sendReceive(9), sendOnly(10), receiveOnly(11), deferReceive(12), deferDeallocate(13), syncpoint(14), syncpointSend(15), syncpointDeallocate(16), backoutRequired(17) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the state of the conversation at the instant when the information was retrieved. The values are: reset The conversation is reset (i.e., deallocated). send The conversation can send data. This value also is returned if the conversation is in Send-Pending state. receive The conversation can receive data. confirm The conversation has received a confirm indicator. It can issue an [MC_]CONFIRMED or [MC_]SEND_ERROR verb to change state. It will continue in Receive state if an [MC_]CONFIRMED verb is issued. confirmSend The conversation is in Confirm state and changes to Send state when an [MC_]CONFIRMED verb is issued. confirmDealloc The conversation is in Confirm state and becomes inactive when an [MC_]CONFIRMED verb is issued. pendingDeallocate The conversation is in Pending-Deallocate state while it waits for (MC_)DEALLOCATE TYPE (sync_level) to complete. pendingPost The conversation is in Pending-Post state while it waits for the [MC_]RECEIVE_AND_POST verb to complete its receive function. sendReceive The full-duplex conversation can send or receive data. sendOnly The full-duplex conversation can send data, but it does not have permission to receive data, because the partner TP has already deallocated its side of the conversation. receiveOnly The full-duplex conversation can receive data, but it does not have permission to send data, because it has already deallocated its side of the conversation. deferReceive Waiting for a successful SYNCPT verb operation to go into the receive state. deferDeallocate Waiting for a successful SYNCPT verb operation to go into the reset state. syncpoint Need to response to a SYNCPT verb issued. After successful operation, the next state will be receive. syncpointSend Need to response to a SYNCPT verb issued. After successful operation, the next state will be send. syncpointDeallocate Need to response to a SYNCPT verb issued. After successful operation, the next state will be reset. backoutRequired TP must execute a BACKOUT verb to backout the transaction." ::= { appcActiveConvEntry 5 } -
appcActiveConvType OBJECT-TYPE
-
SYNTAX INTEGER { basic(1), mapped(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of conversation. The values are:-
-
-
basic
-
-
Indicates that this conversation supports basic verbs.
-
mapped
-
-
Indicates that this conversation supports mapped verbs."
-
-
-
::= { appcActiveConvEntry 6 } -
appcActiveConvCorrelator OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is an 8-byte identifier that the source LU assigns to the conversation; the source LU is the one that sent the allocation request. The conversation correlator is included on the allocation request. The conversation correlator uniquely-
-
identifies a conversation, from among all conversations, between the local and partner LUs. It may be used, for example, during problem determination associated with a conversation. A length of 0 indicates that no conversation correlator is defined."
-
::= { appcActiveConvEntry 7 } -
appcActiveConvSyncLvl OBJECT-TYPE
-
SYNTAX INTEGER { none(1), confirm(2), syncpt(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the highest sync level support for the conversation. The values are:-
-
-
none
-
-
Indicates that no sync-level processing can be performed on this conversation. The transaction program does not issue verbs or recognize any returned parameters
relating to any sync-level function.
-
confirm
-
-
Indicates that confirmation processing can be performed on this conversation. The transaction program can issue verbs and recognize returned parameters relating to confirmation.
-
syncpt
-
-
Indicates that syncpt and confirmation processing can be performed on this conversation. The transaction program can issue verbs and recognize returned parameters relating to syncpt and confirmation."
-
-
-
::= { appcActiveConvEntry 8 } -
appcActiveConvSource OBJECT-TYPE
-
-
SYNTAX INTEGER {
localLu(1), partnerLu(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the local or partner LU is the source of the conversation, that is, which LU started the conversation by sending the allocation request.-
-
-
localLu
-
-
The local LU is the source of the conversation, and the partner LU is the target of the conversation.
-
partnerLu
-
-
The partner LU is the source of the conversation, and the local LU is the target of the conversation."
-
-
-
::= { appcActiveConvEntry 9 } -
appcActiveConvDuplex OBJECT-TYPE
-
SYNTAX INTEGER { half(1), full(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the conversation duplex style in effect for the conversation. half Indicates that information can be transferred in both directions, but only in one direction at a time. full Indicates that information can be transferred in both directions at the same time." ::= { appcActiveConvEntry 10 }
appcActiveConvUpTime OBJECT-TYPE
-
-
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The length of time since the conversation started, measured in hundredths of a second."
-
::= { appcActiveConvEntry 11 } -
appcActiveConvSendBytes OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Indicates the number of bytes that was sent on the conversation. The count includes all SNA RU bytes sent, including those in the FMH-5 (Attach), FMH-7 (Error Description), SIGNAL, LUSTAT, and SNA responses; it does not include SNA TH and RH bytes."
-
::= { appcActiveConvEntry 12 } -
appcActiveConvRcvBytes OBJECT-TYPE
-
-
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"Indicates the number of bytes that was received on the conversation. The count includes all SNA RU bytes sent, including those in the FMH-5 (Attach), FMH-7 (Error Description), SIGNAL, LUSTAT, and SNA responses; it does not include SNA TH and RH bytes."
-
::= { appcActiveConvEntry 13 } -
appcActiveConvUserid OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The user ID that the initiating program provided in the incoming attach." ::= { appcActiveConvEntry 14 }
appcActiveConvPcidNauName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0 | 3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network-qualified NAU name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the-
-
NetId from the NAU name. A null string indicates
that the value is unknown."
-
::= { appcActiveConvEntry 15 } -
appcActiveConvPcid OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0|8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The procedure correlation identifier (PCID) of the session. It is an 8-octet value assigned by the control point providing session services for the primary LU. A null string indicates that the value is unknown." ::= { appcActiveConvEntry 16 }
appcActiveConvModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Mode Name used for this conversation. This is a 1-8 character name." ::= { appcActiveConvEntry 17 }
appcActiveConvLuwIdName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the LU that initiated the logical unit of work that is associated with this active TP. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the LU name if the NetId is present." ::= { appcActiveConvEntry 18 }
appcActiveConvLuwIdInstance OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0..6)) MAX-ACCESS read-only STATUS current DESCRIPTION "The instance identifier for the logical unit of work." ::= { appcActiveConvEntry 19 }
appcActiveConvLuwIdSequence OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0..2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence identifier for the logical unit of work." ::= { appcActiveConvEntry 20 }
appcActiveConvTpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The transaction program name which started this conversation. This name could either be from a FMH5 ATTACH for a remotely started conversation, otherwise it could the name of the local TP if available.-
-
When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes).
This name is NULL if the conversation is started locally (i.e., not with a FMH5 ATTACH)."
-
-
::= { appcActiveConvEntry 21 }
-- *********************************************************************
-- APPC Historical Conversation Table
-- This table contains historical information about APPC
-- conversations that ended abnormally. It is an implementation
-- choice how long to retain information on a given conversation.
-- *********************************************************************
appcHistConvTable OBJECT-TYPE
-
-
SYNTAX SEQUENCE OF AppcHistConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Table of historical information about APPC Conversations that ended in error. Possible categories of error conditions that could be saved in this table are:
-
- allocation errors, - deallocate abend, - program errors, and - service errors." ::= { appcConversation 2 } -
appcHistConvEntry OBJECT-TYPE
-
-
SYNTAX AppcHistConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry representing one APPC Conversation."
INDEX
-
-
{ appcHistConvIndex }
::= { appcHistConvTable 1}
AppcHistConvEntry ::= SEQUENCE {
appcHistConvIndex Integer32,
appcHistConvEndTime DateAndTime,
appcHistConvLocLuName DisplayString,
appcHistConvParLuName DisplayString,
appcHistConvTpName DisplayString,
appcHistConvPcidNauName DisplayString,
appcHistConvPcid OCTET STRING,
appcHistConvSenseData SnaSenseData,
appcHistConvLogData OCTET STRING,
appcHistConvEndedBy INTEGER
}
appcHistConvIndex OBJECT-TYPE
-
-
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Index for entry in Conversation table. This value identifies the unique index of the conversation. It is recommended that an Agent not reuse the index of a deactivated conversation for a significant period of time (e.g. one week)."
-
::= { appcHistConvEntry 1 } -
appcHistConvEndTime OBJECT-TYPE
-
-
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The time at which the conversation ended."
-
::= { appcHistConvEntry 2 } -
appcHistConvLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the local LU for this conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcHistConvEntry 3 }
appcHistConvParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the partner LU for the conversation. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcHistConvEntry 4 }
appcHistConvTpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The transaction program name which started this conversation. This name could either be from a FMH5 ATTACH for a remotely started conversation, otherwise it could the name of the local TP if available.-
-
When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non- displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a
-
-
hexadecimal display of the EBCDIC code points. For example,
the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte
ASCII display string '06F1' (including the two single quotes).
-
-
-
This name is NULL if the conversation is started locally (i.e., not with a FMH5 ATTACH)."
-
::= { appcHistConvEntry 5 } -
appcHistConvPcidNauName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0 | 3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network-qualified NAU name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name. A null string indicates that the value is unknown." ::= { appcHistConvEntry 6 }
appcHistConvPcid OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0|8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The procedure correlation identifier (PCID) of the session. It is an 8-octet value assigned by the control point providing session services for the primary LU. A null string indicates that the value is unknown." ::= { appcHistConvEntry 7 }
appcHistConvSenseData OBJECT-TYPE
-
-
SYNTAX SnaSenseData
MAX-ACCESS read-only
STATUS current
DESCRIPTION-
"The sense data associated with the action that ended this conversation, e.g., FMH-7 or UNBIND."
-
::= { appcHistConvEntry 8 } -
appcHistConvLogData OBJECT-TYPE
-
SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The first 32 bytes of the data portion of the Log Data GDS Variable that is associated with the last FMH-7 that occurred on this conversation. If there was no Log Data GDS Variable associated with the FMH-7, this object is null.-
-
This object reflects only the data portion of the Log Data GDS Variable (i.e. not the LL or GDS Id)."
-
::= { appcHistConvEntry 9 } -
appcHistConvEndedBy OBJECT-TYPE
SYNTAX INTEGER {
localLu(1),
partnerLu(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates which LU ended the conversation."
::= { appcHistConvEntry 10 }
-- *********************************************************************
-- APPC CPIC Admin Table
-- Objects in this table contain default or expected configuration
-- values for CPI-C side information.
-- *********************************************************************
appcCpicAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcCpicAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC CPI-C side information table."
::= { appcCPIC 1 }
appcCpicAdminEntry OBJECT-TYPE
-
-
SYNTAX AppcCpicAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry of APPC CPI-C side information Table."
INDEX { appcCpicAdminLocLuName,
-
appcCpicAdminSymbDestName } ::= { appcCpicAdminTable 1 } -
AppcCpicAdminEntry ::= SEQUENCE {
-
appcCpicAdminLocLuName DisplayString, appcCpicAdminSymbDestName DisplayString, appcCpicAdminParLuAlias DisplayString, appcCpicAdminParLuName DisplayString, appcCpicAdminModeName DisplayString, appcCpicAdminTpNameType INTEGER, appcCpicAdminTpName DisplayString, appcCpicAdminUserid DisplayString, appcCpicAdminSecurity INTEGER }
appcCpicAdminLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU to which this CPI-C side information definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
The reserved value '*ALL' indicates that the definition applies to all local LUs, and not just to a single local LU."
-
::= { appcCpicAdminEntry 1 } -
appcCpicAdminSymbDestName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the symbolic destination name used by CPI-C applications to identify this definition." ::= { appcCpicAdminEntry 2 }
appcCpicAdminParLuAlias OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "A local alias for the partner LU. If not known or-
-
not applicable, this object contains a zero-length
string."
-
::= { appcCpicAdminEntry 3 } -
appcCpicAdminParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcCpicAdminEntry 4 }
appcCpicAdminModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters)." ::= { appcCpicAdminEntry 5 }
appcCpicAdminTpNameType OBJECT-TYPE
-
SYNTAX INTEGER { normal(1), snaServiceTp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the TP name in appcCpicAdminTpName identifies a normal TP or an SNA service TP. In this context, a normal TP is one with a name consisting only of displayable characters, while an SNA service TP has a name containing octets that do not map to displayable characters." ::= { appcCpicAdminEntry 6 }
appcCpicAdminTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..64))
-
MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the name of the partner TP to be used when a CPI-C application initiates a conversation specifying this side information entry. Display convention-
-
-
When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes)."
-
-
::= { appcCpicAdminEntry 7 } -
appcCpicAdminUserid OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The security userid, if any, associated with the side information definition." ::= { appcCpicAdminEntry 8 }
appcCpicAdminSecurity OBJECT-TYPE
SYNTAX INTEGER {
none(1),
same(2),
pgm(3),
pgmStrong(4),
distributed(5),
mutual(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the security information to be used for allocating
the conversation.
none - No security information.
same - Use the security environment currently
associated with this TP.
pgm - Use the program-supplied user_id and password.
pgmStrong - Use the program-supplied user_id and password.
The local LU will insure that the password is
not exposed in clear-text form on the physical
network.
distributed - Use the security environment and a distributed
security system to generate the authentication
information for this request. If distributed
security tokens cannot be generated, then fail
the conversation.
mutual - Authenticate both the user to the destination
system and the destination system to the user."
::= { appcCpicAdminEntry 9 }
-- *********************************************************************
-- APPC CPIC Oper Table
-- Objects in this table contain current operational values, such
-- as state values or negotiated parameters, for CPI-C side
-- information.
-- *********************************************************************
appcCpicOperTable OBJECT-TYPE
-
-
SYNTAX SEQUENCE OF AppcCpicOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"APPC CPI-C side information operational table."
-
::= { appcCPIC 2 } -
appcCpicOperEntry OBJECT-TYPE
-
-
SYNTAX AppcCpicOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION-
"Entry of APPC CPI-C side information Table."
INDEX { appcCpicOperLocLuName,
-
appcCpicOperSymbDestName } ::= { appcCpicOperTable 1 } -
AppcCpicOperEntry ::= SEQUENCE {
-
appcCpicOperLocLuName DisplayString, appcCpicOperSymbDestName DisplayString, appcCpicOperParLuAlias DisplayString, appcCpicOperParLuName DisplayString, appcCpicOperModeName DisplayString, appcCpicOperTpNameType INTEGER, appcCpicOperTpName DisplayString, appcCpicOperUserid DisplayString, appcCpicOperSecurity INTEGER }
appcCpicOperLocLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNA name of the local LU to which this CPI-C side information definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present.-
-
The reserved value '*ALL' indicates that the definition applies to all local LUs, and not just to a single local LU."
-
::= { appcCpicOperEntry 1 } -
appcCpicOperSymbDestName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the symbolic destination name used by CPI-C applications to identify this definition." ::= { appcCpicOperEntry 2 }
appcCpicOperParLuAlias OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string." ::= { appcCpicOperEntry 3 }
appcCpicOperParLuName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the NetId is present." ::= { appcCpicOperEntry 4 }
appcCpicOperModeName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters)." ::= { appcCpicOperEntry 5 }
appcCpicOperTpNameType OBJECT-TYPE
-
SYNTAX INTEGER { normal(1), snaServiceTp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the TP name in appcCpicOperTpName identifies a normal TP or an SNA service TP. In this context, a normal TP is one with a name consisting only of displayable characters, while an SNA service TP has a name containing octets that do not map to displayable characters." ::= { appcCpicOperEntry 6 }
appcCpicOperTpName OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the name of the partner TP to be used when a CPI-C application initiates a conversation specifying this side information entry. Display convention-
-
-
When the TP name consists entirely of displayable EBCDIC code points, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC code point (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC code points. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte ASCII display string '06F1' (including the two single quotes)."
-
-
::= { appcCpicOperEntry 7 } -
appcCpicOperUserid OBJECT-TYPE
-
SYNTAX DisplayString (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The security userid, if any, associated with the active side information definition." ::= { appcCpicOperEntry 8 }
appcCpicOperSecurity OBJECT-TYPE
SYNTAX INTEGER {
none(1),
same(2),
pgm(3),
pgmStrong(4),
distributed(5),
mutual(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the security information to be used for allocating
the conversation.
none - No security information.
same - Use the security environment currently
associated with this TP.
pgm - Use the program-supplied user_id and password.
pgmStrong - Use the program-supplied user_id and password.
The local LU will insure that the password is
not exposed in clear-text form on the physical
network.
distributed - Use the security environment and a distributed
security system to generate the authentication
information for this request. If distributed
security tokens cannot be generated, then fail
the conversation.
mutual - Authenticate both the user to the destination
system and the destination system to the user."
::= { appcCpicOperEntry 9 }
-- ***************************************************************
-- Conformance information
-- ***************************************************************
appcConformance OBJECT IDENTIFIER ::= {appcMIB 2 }
appcCompliances OBJECT IDENTIFIER ::= {appcConformance 1 }
appcGroups OBJECT IDENTIFIER ::= {appcConformance 2 }
-- Compliance statements
appcCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMPv2 entities which
implement the APPC MIB."
MODULE -- this module
-- Unconditionally mandatory groups
MANDATORY-GROUPS {
appcGlobalConfGroup,
appcLluConfGroup,
appcParLuConfGroup,
appcModeConfGroup,
appcTpConfGroup,
appcSessionConfGroup
}
-- Conditionally mandatory groups
GROUP appcControlConfGroup
DESCRIPTION
"The appcControlConfGroup is mandatory only for those
entities which implement activation and deactivation of
specific controls such as statistics collecting and
counting."
GROUP appcCnosConfGroup
DESCRIPTION
"The appcCnosConfGroup is mandatory only for those entities
which implement CNOS. "
GROUP appcCpicConfGroup
DESCRIPTION
"The appcCpicConfGroup is mandatory only for those entities
which implement CPI-C. "
GROUP appcConversationConfGroup
DESCRIPTION
"The appcConversationConfGroup is mandatory only for those
entities which implement session endpoints for non-control
APPC sessions."
-- MIN-ACCESS for objects
OBJECT appcActSessOperState
MIN-ACCESS read-only
DESCRIPTION
"An implementation is not required to support session
deactivation via this object."
::= {appcCompliances 1 }
-- Units of conformance
appcGlobalConfGroup OBJECT-GROUP
OBJECTS {
appcUpTime,
appcDefaultModeName,
appcDefaultLuName,
appcDefaultImplInbndPlu,
appcDefaultMaxMcLlSndSize,
appcDefaultFileSpec,
appcDefaultTpOperation,
appcDefaultTpConvSecRqd,
appcLocalCpName,
appcActiveSessions,
appcActiveHprSessions
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
global information and defaults."
::= { appcGroups 1 }
appcLluConfGroup OBJECT-GROUP
-
OBJECTS { appcLluAdminDepType, appcLluAdminLocalAddress, appcLluAdminSessLimit, appcLluAdminBindRspMayQ, appcLluAdminCompression, appcLluAdminInBoundCompLevel, appcLluAdminOutBoundCompLevel, appcLluAdminCompRleBeforeLZ, appcLluAdminAlias, appcLluOperDepType, appcLluOperLocalAddress, appcLluOperSessLimit, appcLluOperBindRspMayQ, appcLluOperCompression, appcLluOperInBoundCompLevel, appcLluOperOutBoundCompLevel, appcLluOperCompRleBeforeLZ, appcLluOperAlias, appcLluOperActiveSessions } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC local LU6.2s." ::= { appcGroups 2 }
appcParLuConfGroup OBJECT-GROUP
-
OBJECTS { appcLuPairAdminParLuAlias, appcLuPairAdminSessLimit, appcLuPairAdminSessSec, appcLuPairAdminSecAccept, appcLuPairAdminLinkObjId, appcLuPairAdminParaSessSup, appcLuPairOperParLuAlias, appcLuPairOperSessLimit, appcLuPairOperSessSec, appcLuPairOperSecAccept, appcLuPairOperLinkObjId, appcLuPairOperParaSessSup, appcLuPairOperParaSessSupLS, appcLuPairOperState }-
STATUS current
DESCRIPTION-
"A collection of objects providing the instrumentation of APPC partner LUs."
-
::= { appcGroups 3 } -
appcModeConfGroup OBJECT-GROUP
-
OBJECTS { appcModeAdminCosName, appcModeAdminSessEndTpName, appcModeAdminMaxSessLimit, appcModeAdminMinCwinLimit, appcModeAdminMinClosLimit, appcModeAdminConWinAutoActLmt, appcModeAdminRecvPacWinSz, appcModeAdminSendPacWinSz, appcModeAdminPrefRecvRuSz, appcModeAdminPrefSendRuSz, appcModeAdminRecvRuSzUpBnd, appcModeAdminSendRuSzUpBnd, appcModeAdminRecvRuSzLoBnd, appcModeAdminSendRuSzLoBnd, appcModeAdminSingSessReinit, appcModeAdminCompression, appcModeAdminInBoundCompLevel, appcModeAdminOutBoundCompLevel, appcModeAdminCompRleBeforeLZ, appcModeAdminSyncLvl, appcModeAdminCrypto, appcModeOperCosName, appcModeOperSessEndTpName, appcModeOperSessLimit, appcModeOperMaxSessLimit, appcModeOperMinCwinLimit, appcModeOperMinClosLimit, appcModeOperConWinAutoActLmt, appcModeOperRecvPacWinSz, appcModeOperSendPacWinSz, appcModeOperPrefRecvRuSz, appcModeOperPrefSendRuSz, appcModeOperRecvRuSzUpBnd, appcModeOperSendRuSzUpBnd, appcModeOperRecvRuSzLoBnd, appcModeOperSendRuSzLoBnd, appcModeOperSingSessReinit, appcModeOperCompression, appcModeOperInBoundCompLevel, appcModeOperOutBoundCompLevel, appcModeOperCompRleBeforeLZ, appcModeOperSyncLvl, appcModeOperCrypto, appcModeOperSyncLvlLastStart, appcModeOperCryptoLastStart, appcModeOperCNOSNeg, appcModeOperActCwin, appcModeOperActClos, appcModeOperPndCwin, appcModeOperPndClos, appcModeOperPtmCwin, appcModeOperPtmClos, appcModeOperDrainSelf, appcModeOperDrainPart } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC modes." ::= { appcGroups 4 }
appcTpConfGroup OBJECT-GROUP
-
OBJECTS { appcTpAdminFileSpec, appcTpAdminStartParm, appcTpAdminTpOperation, appcTpAdminInAttachTimeout, appcTpAdminRcvAllocTimeout, appcTpAdminSyncLvl, appcTpAdminInstLmt, appcTpAdminStatus, appcTpAdminLongRun, appcTpAdminConvType, appcTpAdminConvDuplex, appcTpAdminConvSecReq, appcTpAdminVerPip, appcTpAdminPipSubNum } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC Transaction Programs." ::= { appcGroups 5 }
appcSessionConfGroup OBJECT-GROUP
-
OBJECTS { appcActSessPcidCpName, appcActSessPcid, appcActSessPluIndicator, appcActSessModeName, appcActSessCosName, appcActSessTransPriority, appcActSessEnhanceSecSup, appcActSessSendPacingType, appcActSessSendRpc, appcActSessSendNxWndwSize, appcActSessRecvPacingType, appcActSessRecvRpc, appcActSessRecvNxWndwSize, appcActSessRscv, appcActSessInUse, appcActSessMaxSndRuSize, appcActSessMaxRcvRuSize, appcActSessSndPacingSize, appcActSessRcvPacingSize, appcActSessOperState, appcActSessUpTime, appcActSessRtpNceId, appcActSessRtpTcid, appcActSessLinkIndex, appcSessStatsSentFmdBytes, appcSessStatsSentNonFmdBytes, appcSessStatsRcvdFmdBytes, appcSessStatsRcvdNonFmdBytes, appcSessStatsSentFmdRus, appcSessStatsSentNonFmdRus, appcSessStatsRcvdFmdRus, appcSessStatsRcvdNonFmdRus, appcSessStatsCtrUpTime, appcHistSessTime, appcHistSessType, appcHistSessLocLuName, appcHistSessParLuName, appcHistSessModeName, appcHistSessUnbindType, appcHistSessSenseData, appcHistSessComponentId, appcHistSessDetectModule, appcSessRtpSessions } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC LU6.2 sessions." ::= { appcGroups 6 }
appcControlConfGroup OBJECT-GROUP
-
OBJECTS { appcCntrlAdminStat, appcCntrlAdminRscv, appcCntrlAdminTrace, appcCntrlAdminTraceParm, appcCntrlOperStat, appcCntrlOperStatTime, appcCntrlOperRscv, appcCntrlOperRscvTime, appcCntrlOperTrace, appcCntrlOperTraceTime, appcCntrlOperTraceParm } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC control." ::= { appcGroups 7 }
appcCnosConfGroup OBJECT-GROUP
-
OBJECTS { appcCnosCommand, appcCnosMaxSessLimit, appcCnosMinCwinLimit, appcCnosMinClosLimit, appcCnosDrainSelf, appcCnosDrainPart, appcCnosResponsible, appcCnosForce, appcCnosTargetLocLuName, appcCnosTargetParLuName, appcCnosTargetModeName } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC CNOS processing." ::= { appcGroups 8 }
appcCpicConfGroup OBJECT-GROUP
-
OBJECTS { appcCpicAdminParLuAlias, appcCpicAdminParLuName, appcCpicAdminModeName, appcCpicAdminTpNameType, appcCpicAdminTpName, appcCpicAdminUserid, appcCpicAdminSecurity, appcCpicOperParLuAlias, appcCpicOperParLuName, appcCpicOperModeName, appcCpicOperTpNameType, appcCpicOperTpName, appcCpicOperUserid, appcCpicOperSecurity } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC CPI-C side information." ::= { appcGroups 9 }
appcConversationConfGroup OBJECT-GROUP
-
OBJECTS { appcActiveConvId, appcActiveConvState, appcActiveConvType, appcActiveConvCorrelator, appcActiveConvSyncLvl, appcActiveConvSource, appcActiveConvDuplex, appcActiveConvUpTime, appcActiveConvSendBytes, appcActiveConvRcvBytes, appcActiveConvUserid, appcActiveConvPcidNauName, appcActiveConvPcid, appcActiveConvModeName, appcActiveConvLuwIdName, appcActiveConvLuwIdInstance, appcActiveConvLuwIdSequence, appcActiveConvTpName,-
-
-
appcHistConvEndTime,
-
-
appcHistConvLocLuName, appcHistConvParLuName, appcHistConvTpName, appcHistConvPcidNauName, appcHistConvPcid, appcHistConvSenseData, appcHistConvLogData, appcHistConvEndedBy } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC conversations." ::= { appcGroups 10 } -
-- end of conformance statement
END
5. Acknowledgments
-
This MIB module is the product of the SNA NAU MIB Working Group. Special thanks to Wayne Clark, Cisco Systems; Rich Daugherty, IBM Corporation; and Leo Temoshenko, IBM Corporation, for their contributions and review.
6. References
[1] IBM, Systems Network Architecture Technical Overview, GC30-3073-4,
January, 1994.
[2] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Structure of Management Information for version 2 of
the Simple Network Management Protocol (SNMPv2)", RFC 1902, January
1996.
[3] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Textual Conventions for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1903, January 1996.
[4] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Conformance Statements for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1904, January 1996.
[5] IBM, Systems Network Architecture Transaction Programmer's
Reference for LU Type 6.2, GC30-3084-05, June, 1993.
[6] IBM, Common Programming Interface Communications Specification 2.0,
SC31-6180-01, June, 1994.
[7] Kielczewski, Z., Kostick D., and K. Shih, "Definition of Managed
Objects for SNA NAUs using SMIv2", RFC 1666, Eicon Technology
Corporation, Bell Communications Research, Novell, August 1994.
7. Security Considerations
-
Security issues are not discussed in this memo.
8. Authors' Addresses
-
Michael Allen Wall Data Inc. P.O.Box 1120, WA 98019, USA Phone: +1 206 844 3505 EMail: mallen@hq.walldata.com-
Bob Clouston
Cisco Systems
7025 Kit Creek Road
PO Box 14987
Research Triangle Park, NC 27709, USA
Phone: +1 919 472 2333 EMail: clouston@cisco.com-
Zbigniew Kielczewski
Cisco Systems
7025 Kit Creek Road
PO Box 14987
Research Triangle Park, NC 27709, USA
Phone: +1 919 472 2326 EMail: zbig@cisco.com-
William Kwan
Jupiter Technology Inc.
200 Prospect St.
Waltham, MA 02254
Phone: 1 617 894-9300 x423 EMail: billk@jti.com-
Bob Moore
IBM Corporation
800 Park Offices Drive
E87/664
P.O. Box 12195
Research Triangle Park, NC 27709, USA
Phone: 1 919 254 4436 EMail: remoore@ralvm6.vnet.ibm.com -